Grandstream HandyTone 702 - HT702

From VoIP.ms Wiki

GENERAL INFORMATION

The Grandstream HandyTone 702/7XX series is the latest in the HandyTone line. The 702 is a reliable, inexpensive telephone adapter which works with the VoIP.ms service when placed after your broadband internet router.

Websites: HT702 Product Page

Help / Support: Grandstream Support

Configuring the Handytone 702

These instructions are based on HandyTone 702 software version 1.0.0.18; if you are running a different software version some menus and settings may be different.
These instructions are also based on using the HandyTone in its factory default configuration, which obtains a dynamic IP address automatically from your router using DHCP. For information on configuring your HandyTone with a Static IP Address, please refer to the HandyTone user´s manual.

Each step is important in assuring that your device works properly.

 We recommend that you read each step through in its entirety before performing the action indicated in the step. 

Step 1

Connect your HandyTone to your router with the supplied Ethernet network cable.

Now connect your phone to the HandyTone. Plugging the cable into the correct FXS Port that you configure.

Finally plug the supplied power cable into the HandyTone.

Step 2

Wait 60 seconds after plugging your HT702 in.

Pick up the phone connected to the HT702 and dial the * key on your phone 3 times.

Please have a pen and paper ready. You will hear a message - "Enter a menu option", then enter 0 2 on your phone. You will now hear a message giving you the IP address of your HT702 such as - "192.168.001.010" and write this number down.

Open a web browser on your computer such as Chrome or Firefox and enter the IP address you heard in step 4 as the address (I.E. where you would normally enter www.voip.ms).

Please note: Some browsers will require you to remove leading zero's ( 0 's ) in the IP address. For example if you heard "192.168.001.010" you should change this to "192.168.1.10".

Step 3

You should now see a page that looks like this:

Enter the password for the HT702 in the password field. The default administrator password for the HT702 is "admin" (without quotes).

After entering the password you should see a screen that looks similar to the one below:

Step 4

Now, click on FXS PORT1 and configure your settings accordingly (as shown below):

Please use the following settings to configure your VoIP.ms account: Configuration Page Settings:

Primary SIP Server: servername.voip.ms (Pick one of VoIP.ms multiple VoIP Servers)

* You can also find this information by logging into your Customer portal.	

Failover SIP Server: (Please leave this Blank)

Outbound Proxy: servername.voip.ms (Pick one of VoIP.ms multiple VoIP Servers)

 * You can also find this information by logging into your Customer portal.

NAT Traversal (STUN): No, but send keep-alive

SIP User ID: (Replace with your Main SIP account or Subaccount UserID, e.g. 198765 or 198765_sub)

Authenticate ID: (Replace with your Main SIP account or Subaccount UserID, e.g. 198765 or 198765_sub)

Authenticate Password: ****** (Use the SIP account password - By default this is the same as the Customer Portal)

DNS Mode: SRV

SIP Registration: Yes

Unregister On Reboot: Yes

Outgoing Call Without Registration: Yes

Register Expiration: 3

Allow Incoming SIP Messages from SIP Proxy Only: Yes

Preferred DTMF method: In-audio, RFC2833

Enable Call Features: No

Dial Plan: {[x*]+}

Preferred Vocoder: PCMU, G729, PCMA

Step 5

Once you have configured the settings above, click the Update button and then the Reboot button to save the configurations.

Your HT702 will power cycle after you click the reboot button. Please wait at least 30 seconds for the unit to finish power cycling. If you see that the Phone 1 LED (or phone 2 LED, depending on which FXS port you've configured our service for) is a solid green color, then your unit is configured and ready to make calls.

Step 6

That's it! You can now make a phone call.

1 + the area code and number for calls to the US & Canada

Or

011 + the country code, area code, and number for calls worldwide (you may also use 00 instead of 011).