Telco AC-211

From VoIP.ms Wiki

[draft revision]

[draft revision]

Revision as of 19:46, 21 January 2012 (view source) Carlb (Talk | contribs) m (+cat) ← Older edit		Revision as of 17:24, 18 December 2013 (view source) Joseph.voip.ms (Talk | contribs) Newer edit →
Line 7:		Line 7:
	* Enter the IP in the address bar of your browser for the unit		* Enter the IP in the address bar of your browser for the unit
-	* Enter the password for the unit and click Authencate	+	* Enter the password for the unit and click Authenticate
Line 13:		Line 13:
	* Go to '''WAN''' tab		* Go to '''WAN''' tab
-	* Select AutoConfiguration tab and uncheck "Enable Automatic Configuration"	+	* Select auto configuration tab and uncheck "Enable Automatic Configuration"
-	'''SIP Settings'''	+	=='''SIP Settings'''==
	* Go to '''SIP''' tab		* Go to '''SIP''' tab
	* '''Primary Server''': Enter the following.		* '''Primary Server''': Enter the following.
-	**Enter the server name. Example: houston.voip.ms	+	**Enter the server name. Example: atlanta.voip.ms
	**Port 5060		**Port 5060
	**Domain Name: voip.ms		**Domain Name: voip.ms
Line 30:		Line 30:
	**Port*: 5060		**Port*: 5060
	**AEC On: On		**AEC On: On
-	**Authentication User Name: Your SIP Username	+	**Authentication User Name: 100000 (Replace with your SIP Username)
	**Password: SIP Password		**Password: SIP Password
	**Click '''Save SIP Settings'''		**Click '''Save SIP Settings'''
-	'''CODECS'''	+	[[File:telco_211_1.gif]]
		+
		+	=='''CODECS'''==
	* Go to '''CODECS''' tab		* Go to '''CODECS''' tab
	* Force preferred CODEC Line 1: Set your preferred CODEC, recommended is G711U		* Force preferred CODEC Line 1: Set your preferred CODEC, recommended is G711U
	**The CODEC set must be enabled in your account: Account Settings -> Advanced		**The CODEC set must be enabled in your account: Account Settings -> Advanced
	* Click '''Save CODEC Configuration'''		* Click '''Save CODEC Configuration'''
		+
		+	[[File:telco_211_2.gif]]
	'''Miscellaneous'''		'''Miscellaneous'''

---

Revision as of 17:24, 18 December 2013

Contents 1 Configuration Details 2 SIP Settings 3 CODECS 4 Notes

Configuration Details

Web Management

• Enter the IP in the address bar of your browser for the unit
• Enter the password for the unit and click Authenticate

WAN Settings

• Go to WAN tab
• Select auto configuration tab and uncheck "Enable Automatic Configuration"

SIP Settings

• Go to SIP tab
• Primary Server: Enter the following.
  • Enter the server name. Example: atlanta.voip.ms
  • Port 5060
  • Domain Name: voip.ms
  • Check "Send Registration Request"
  • Dial Plan: (>#|[2-9]xxxxxxxxx|1[2-9]xxxxxxxxx|0|[489]11|*9[7-8]|*75xx)
  • Transport: UDP
  • User/Phone Num: Your SIP Username
  • CallerID Name: Enter the CID you want to send
  • Port*: 5060
  • AEC On: On
  • Authentication User Name: 100000 (Replace with your SIP Username)
  • Password: SIP Password
  • Click Save SIP Settings

CODECS

• Go to CODECS tab
• Force preferred CODEC Line 1: Set your preferred CODEC, recommended is G711U
  • The CODEC set must be enabled in your account: Account Settings -> Advanced
• Click Save CODEC Configuration

Miscellaneous

• Go to Miscellaneous tab
• Enter an NTP server
  • Free NTP Servers available at http://www.pool.ntp.org/en/
  • Click Save Settings

Reset

• Click the Reset button to reboot the gateway

Notes

• Under the SIP Server Settings the device supports a fail over server, but at this time the server does not support this. Leave this blank or you will have problems receiving incoming calls.
• The dial plan supports 10 & 11 digit dialing, *97 & *98 for voice mail, *75 dialing from the phonebook, 411, 811, & 911.
• When modifying the dialing plan >#| is required at the start of the plan, though I don't know why.