Cisco SPA941
From VoIP.ms Wiki
| [draft revision] | [quality revision] |
m (+cat) |
|||
| (7 intermediate revisions not shown) | |||
| Line 3: | Line 3: | ||
| - | The Linksys SPA941 IP telephone can be configured as a two | + | The Linksys SPA941 IP telephone can be configured as a two line or, via a simple software upgrade, a 4 line full phone with pixel based graphical display, speakerphone and headset port.It is configured for DHCP, this means that it gets its IP address from your DHCP server automatically. |
| + | |||
| - | |||
'''STEP 1''' | '''STEP 1''' | ||
| + | |||
Press the Paper "button" and then press number 9 which will take you into the network settings. Option 2 will show you the phone's IP address. | Press the Paper "button" and then press number 9 which will take you into the network settings. Option 2 will show you the phone's IP address. | ||
'''STEP 2''' | '''STEP 2''' | ||
| - | Go to any browser equipped computer on your network and enter the address: http://<IP ADDRESS>/ | + | |
| - | + | Go to any browser equipped computer on your network and enter the address: http://<IP ADDRESS HERE>/ | |
| + | |||
'''STEP 3''' | '''STEP 3''' | ||
| + | |||
Click on the "Admin Login" button near the top right side of the screen, then click on the "Ext 1" tab. | Click on the "Admin Login" button near the top right side of the screen, then click on the "Ext 1" tab. | ||
| + | |||
[[File:Linksys-942-2.gif]] | [[File:Linksys-942-2.gif]] | ||
| + | |||
'''STEP 4''' | '''STEP 4''' | ||
| + | |||
You need to modify only a few parameters from the factory default. They are listed here: | You need to modify only a few parameters from the factory default. They are listed here: | ||
*'''SIP Port''': 5060 | *'''SIP Port''': 5060 | ||
*'''Proxy''': Houston.voip.ms (you server) | *'''Proxy''': Houston.voip.ms (you server) | ||
*'''RegisterExpires''': 180 | *'''RegisterExpires''': 180 | ||
| - | *'''User ID''': Your user ID (123456) main account or sub account (123456_xxx) | + | *'''User ID''': Your user ID (i.e. 123456) main account or sub account (i.e. 123456_xxx) |
*'''Password''': Enter the password that you chose when you signed up your voip.ms service. | *'''Password''': Enter the password that you chose when you signed up your voip.ms service. | ||
*'''Preferred Codec''': G729a | *'''Preferred Codec''': G729a | ||
| + | *'''Use Pref Codec Only''': no | ||
[[File:Linksys SPA941 Configurationjpg.jpg]] | [[File:Linksys SPA941 Configurationjpg.jpg]] | ||
'''STEP 5''' | '''STEP 5''' | ||
| - | If the second extension is needed, click on Ext2 and repeat Step 4 | + | |
| + | If the second extension is needed, click on Ext2 and repeat Step 4. | ||
'''STEP 6''' | '''STEP 6''' | ||
| + | |||
You are ready to make some test and calls. | You are ready to make some test and calls. | ||
| + | |||
| + | Note: We have seen some customers installing the SPA941 behind a firewall which blocks ICMP packets causes problems with registration. Try turning off anything blocking your firewall. | ||
| + | [[category:SIP phones]] | ||
Latest revision as of 19:55, 21 January 2012
Device Configuration Guides Linksys SPA941 NA
The Linksys SPA941 IP telephone can be configured as a two line or, via a simple software upgrade, a 4 line full phone with pixel based graphical display, speakerphone and headset port.It is configured for DHCP, this means that it gets its IP address from your DHCP server automatically.
STEP 1
Press the Paper "button" and then press number 9 which will take you into the network settings. Option 2 will show you the phone's IP address.
STEP 2
Go to any browser equipped computer on your network and enter the address: http://<IP ADDRESS HERE>/
STEP 3
Click on the "Admin Login" button near the top right side of the screen, then click on the "Ext 1" tab.
STEP 4
You need to modify only a few parameters from the factory default. They are listed here:
- SIP Port: 5060
- Proxy: Houston.voip.ms (you server)
- RegisterExpires: 180
- User ID: Your user ID (i.e. 123456) main account or sub account (i.e. 123456_xxx)
- Password: Enter the password that you chose when you signed up your voip.ms service.
- Preferred Codec: G729a
- Use Pref Codec Only: no
STEP 5
If the second extension is needed, click on Ext2 and repeat Step 4.
STEP 6
You are ready to make some test and calls.
Note: We have seen some customers installing the SPA941 behind a firewall which blocks ICMP packets causes problems with registration. Try turning off anything blocking your firewall.
