Zycoo ZP502

From VoIP.ms Wiki

[draft revision]

[quality revision]

Revision as of 19:56, 14 June 2011 (view source) Eric.voip.ms (Talk | contribs) ← Older edit		Latest revision as of 19:45, 21 January 2012 (view source) Carlb (Talk | contribs) (+cat)
(7 intermediate revisions not shown)
Line 6:		Line 6:
	'''Step 1'''		'''Step 1'''
-	The first step is to find out what IP Address your adapter is currently using. To do this, pick a phone connected on Line 1 and do the following:	+	Once you confirm this phone is connected to your network, from your PC ( which should be connected to the network too ), enter the IP address of the wan port in this phone as the URL (e.g. http://xxx.xxx.xxx.xxx/ or http://xxx.xxx.xxx.xxx:xxxx/).  If you do not know the IP address, you can look it up on the phone’s display by pressing navigation "down" button.
-	'''Dial: **** (That is 4 asterisks)'''<br>	+	In the login page you will need to enter the username and password:
-	'''Once this is done, dial: 110# (110 followed by a square)'''	+
-	The system should now playback the IP Address your device has been assigned.<br>	+	1. Default user with general level -> username：guest / password：guest
-	(Example: 192.168.1.2)	+
		+	2. Default user with root level -> username：admin / password：admin
		+
		+	The default password of phone screen menu is 123. After you configure the ip phone, you need click save button in config under Maintenance
		+	in the left catalog to save your configuration. Otherwise the phone will lose your modification after power off and on.
	'''Step 2'''		'''Step 2'''
-	'''Using your favorite web browser from a computer on the same network, point the address to the IP address of your adapter.'''<br>	+	Once you enter on the configuration portal of this device, please go to VOIP section, there you can see a screen like this:
-	<nowiki>(example http://192.168.1.2)</nowiki> Replace 192.168.1.2 by the IP Address your device is currently using.	+
		+	[[File:ZP502SIP.JPG|Zycoo ZP502 Configuration Screen]]
		+	First you need to select the SIP line you will use, then you can set the following information on
-	'''Step 3'''	+	'''BASIC SETTING'''
-	You should now see the web interface of your Linksys/Sipura.	+	'''Server Address''': houston.voip.ms( or IP address of any of our servers )
-	'''click on the link "Admin", and once the page has reloaded, click again on the link "Advanced View".'''	+	'''Server Port''': 5060 ( if this is blocked on your side, you can try with port 5080 )
		+	'''Account Name''': 1XXXXX or 1XXXXX_X ( here you need to enter your main account or a sub account )
		+	'''Password''' : your account or sub account password
-	'''Step 4'''	+	'''Phone Number''': 1XXXXX or 1XXXXX_X ( here you need to enter your main account or a sub account )
-	'''Under the LINE 1 Tab, Find the following fields and fill them with the following information'''	+	'''Enable Register''': Mark this box
-	'''Proxy:''' atlanta.voip.ms (one of our multiple servers)<br>
-	'''Display Name:''' John Smith (your name or company name)<br>
-	'''User ID:''' 100000 (your VoIP.ms username)<br>
-	'''Password:''' ******** (the account password)<br>
-	'''Register Expires:''' 180<br>
-	'''Proxy Fallback Intvl:''' 180<br>
-	'''Nat Keep Alive:''' Yes<br>
-	'''Nat Mapping/Traversal:''' Yes
		+	'''ADVANCED SIP SETTING'''
		+	'''Register expire time''': 180
-	'''Step 5 (Optional)'''	+	'''NAT keep Alive interval''': 180
-	Optionally, To save bandwidth, you can change Line 1 "Preferred Codec" to G729a and make sure "Use Pref Codec Only" is set to no.	+	'''Local Port''': 5060 ( if this is blocked on your side, you can try with port 5080 )
		+	'''NAT Keep Alive''': Mark this box
		+	'''Transport Protocol''': UDP
-	'''Step 6 (Optional)'''	+	Finally, you need to click on button "APPLY" to save these changes.
-	Optionally, you can configure your adapter with a better dial plan, allowing faster dialing of 10 digits number (Local US/Canada) and also enable 7 digits dialing in one area code of your choice.
-	'''At the bottom of Line 1 TAB, you will find a field called Dial Plan'''	+	'''Step 3 (OPTIONAL)'''
-	Replace the 555 digits in the following line by the area code of your choice and copy the line, including parenthesis, in the Dialplan field in Line 1 Tab at the bottom of the page:	+	In case you want to use IAX2 protocol, once you select IAX2 Tab you can see a screen like this:
-	(<:1555>[2-9]xxxxxx|1[2-9]xx[2-9]xxxxxxS0|[2-9]xx[2-9]xxxxxxS0|*xx|*xx.|[3468]11|911S0|822|0|00|[2-9]xxxxxx|4XXX|xxxxxxxxxxxx.)	+	[[File:ZP502IAX.JPG|Zycoo ZP502 Configuration Screen]]
		+	There you can set the following information
-	'''Step 7'''	+	'''IAX2 Server Addr''': houston.voip.ms( or IP address of any of our servers )
-	Click on the "Save Settings " button at the bottom of the form.	+	'''IAX2 Server Port''': 4569 ( if this is blocked on your side, you can try with port 5080 )
		+	'''Account Name''': 1XXXXX or 1XXXXX_X ( here you need to enter your main account or a sub account )
-	'''Configuration Screens'''	+	'''Account Password''' : your account or sub account password
		+	'''Phone Number''': 1XXXXX or 1XXXXX_X ( here you need to enter your main account or a sub account )
-	[[File:ZP502SIP.JPG|PAP2T Configuration Screen|frame|left]]	+	'''Local Port''': 4569 ( if this is blocked on your side, you can try with port 5080 )
		+	'''Enable Register''': Mark this box
-	[[File:ZP502IAX.JPG|PAP2T Configuration Screen|frame|left]]	+	Finally, you need to click on button "APPLY" to save these changes.
		+	[[Category:SIP phones]]

---

Latest revision as of 19:45, 21 January 2012

Configuration Details

Step 1

Once you confirm this phone is connected to your network, from your PC ( which should be connected to the network too ), enter the IP address of the wan port in this phone as the URL (e.g. http://xxx.xxx.xxx.xxx/ or http://xxx.xxx.xxx.xxx:xxxx/). If you do not know the IP address, you can look it up on the phone’s display by pressing navigation "down" button.

In the login page you will need to enter the username and password:

1. Default user with general level -> username：guest / password：guest

2. Default user with root level -> username：admin / password：admin

 The default password of phone screen menu is 123. After you configure the ip phone, you need click save button in config under Maintenance 
 in the left catalog to save your configuration. Otherwise the phone will lose your modification after power off and on.

Step 2

Once you enter on the configuration portal of this device, please go to VOIP section, there you can see a screen like this:

First you need to select the SIP line you will use, then you can set the following information on

BASIC SETTING

Server Address: houston.voip.ms( or IP address of any of our servers )

Server Port: 5060 ( if this is blocked on your side, you can try with port 5080 )

Account Name: 1XXXXX or 1XXXXX_X ( here you need to enter your main account or a sub account )

Password : your account or sub account password

Phone Number: 1XXXXX or 1XXXXX_X ( here you need to enter your main account or a sub account )

Enable Register: Mark this box

ADVANCED SIP SETTING

Register expire time: 180

NAT keep Alive interval: 180

Local Port: 5060 ( if this is blocked on your side, you can try with port 5080 )

NAT Keep Alive: Mark this box

Transport Protocol: UDP

Finally, you need to click on button "APPLY" to save these changes.

Step 3 (OPTIONAL)

In case you want to use IAX2 protocol, once you select IAX2 Tab you can see a screen like this:

There you can set the following information

IAX2 Server Addr: houston.voip.ms( or IP address of any of our servers )

IAX2 Server Port: 4569 ( if this is blocked on your side, you can try with port 5080 )

Account Name: 1XXXXX or 1XXXXX_X ( here you need to enter your main account or a sub account )

Account Password : your account or sub account password

Phone Number: 1XXXXX or 1XXXXX_X ( here you need to enter your main account or a sub account )

Local Port: 4569 ( if this is blocked on your side, you can try with port 5080 )

Enable Register: Mark this box

Finally, you need to click on button "APPLY" to save these changes.