Vtech VSP Series - VoIP.ms Wiki

Vtech VSP Series

From VoIP.ms Wiki

Jump to: navigation, search
VSP736 ErisTerminal.jpg


While the screenshots used for this guide were taken from a VSP736, the steps and configuration apply for the VSP6XX and VSP7XX series, specifically tested with:
  • VSP 715
  • VSP 725
  • VSP 726
  • VSP 736
  • VSP 600

The Vtech VSP700 Series comes with all the essential features you need to keep pace with your business and your budget. Depending on the model, support two to six SIP accounts with these easy-to-use phones.

Enjoy all the PBX features and functionality you're used to—and more: Advanced call handling, HD voice quality, Flexibility, Call recording with micro SD card slot (VSP726, VSP736 and VSP861 only), Intuitive design, Dual Ethernet ports, One-button call routing, Power over Ethernet (PoE), and Full-duplex speakerphone.


Contents


Accessing The Web Interface

In order to configure the VSP7XX to be used along with our service, it is required to access it's web interface settings. For this, the IP address of the device must be acquired.

To perform this click on the "Menu" button of the phone. Once on the settings menu, scroll down to: " Status " , then select: " Network ". On this section, you'll need to take note of the IP address shown beside: " IP ". It should read back something as: " 192.168.0.1 ".

Once you have the IP address please open a web browser of your preference and it's URL bar enter the IP address you got by prepending: " http:// " and access it. Once accessed, you'll be prompted to authenticate.

Default's credentials are:
user: admin
password: admin

System configuration

Once logged in you'll be presented with this screen:

VSP7XXSystemStatus.PNG

Here, please navigate to: System. Once on this page, select Account 1 under "SIP account Management" from the colum on the left (or the one you will configure):

System Account Management Account X

General Account Settings

  • Account Label:: The name you wish to pass when calling out
  • Display Name: The name you wish to pass when calling out
  • User Identifer: 100000 (replace with your SIP main account or subaccount)
  • Authentication Name: 100000 (replace with your SIP main account or subaccount)
  • Authentication Password: Your SIP account's password
  • Dial Plan: x+P (By default)
VSP7XXAccountSettings.PNG

SIP Server

  • Server Address: One of VoIP.ms multiple SERVERS, you can choose the one closest to your location
  • Port: 5060 (Aditionally you could use 5080 or 42872)

Registration

  • Server Address: Be sure that you use the same one you used at Server Address
  • Port: 5060 (Aditionally you could use 5080 or 42872)
  • Expiration (secs): 300
  • Registration Freq (secs): 10

Outbound Proxy

  • Server Address: Be sure that you use the same one you used at Server Address
  • Port: 5060 (Aditionally you could use 5080 or 42872)

Backup Outbound Proxy

Leave these settings as they are by default

Audio

We strongly recommend to have set here only the audio codec(s) you have enabled in your SIP account's settings (preferrably only one). In case you need to have more than 1 Audio codec, it can be set as follows:

  • Ringer Tone: 1 (or the one you prefer)
  • Codec Priority 1: G.711u
  • Codec Priority 2: G.729a/b
  • Codec Priority 3: None
  • Codec Priority 4: None
  • Codec Priority 5: None
  • Codec Priority 6: None
  • Codec Priority 7: None
VSP7XXAccountSettings2.PNG

Signaling Settings

  • Local SIP Port: 5060 (Aditionally you could use 5080 or 42872)
  • Transport: UDP or TCP (Depending on your network's configuration)


You can leave all the other values as they are unless you actually need to specify them.

Scroll down and click on "Save" then you can go back to the "Status" tab, if all is correct, you will see your account as Registered

VSP7XXRegistered.PNG


Using TLS/Encryption

The Vtech VSP7XX device series is compatible with Call Encryption. However, to use it, you need to change some settings on your device:

Ports for TLS

When you enable encryption calls from our system, the ports need to be changed to the encrypted ones. This is just adding " 1 " to the used port, leaving the available ones like 5061, 5081, 42873. Make the proper changes in your device's settings to have it working

Audio Section

Mark this "[]Enable Voice Encryption (SRTP)"

  • VSP7XXTLS1.png
  • VSP7XXTLS2.png
Personal tools
Namespaces
Variants
Actions
VoIP.ms Wiki
Configuration
Guides (English)
Guides (Français)
Guías (Español)
Toolbox