Vtech Conference Station
From VoIP.ms Wiki
While the screenshots used for this guide were taken from a VCS754, the steps and configuration also apply for model VCS752
The Vtech VCS754 ErisStation conference phone features a compact, all-in-one design makes it easy to keep everything together—no clutter, no hassle. Built-in charging stations with magnetic bays ensure the microphones are charged and available for the next meeting.
All Eristation conference phones come with portable DECT 6.0 microphones with Orbitlink Wireless Technology, making conference calls more flexible and engaging than ever before.
Contents |
Accessing The Web Interface
In order to configure the VCS754 to be used along with our service, it is required to access it's web interface settings. For this, the IP address of the device must be acquired.
To perform this click on the "Menu" button of the phone. Once on the settings menu, scroll down to: " Status " , then select: " Network ". On this section, you'll need to take note of the IP address shown beside: " IP ". It should read back something as: " 192.168.0.1 ".
Once you have the IP address please open a web browser of your preference and it's URL bar enter the IP address you got by prepending: " http:// " and access it. Once accessed, you'll be prompted to authenticate.
Default's credentials are: user: admin password: admin
System configuration
Once logged in you'll be presented with this screen:
Here, please navigate to: System. Once on this page, select Account 1 under "SIP account Management" from the colum on the left (or the one you will configure):
System Account Management Account X
General Account Settings
- Account Label:: The name you wish to pass when calling out
- Display Name: The name you wish to pass when calling out
- User Identifer: 100000 (replace with your SIP main account or subaccount)
- Authentication Name: 100000 (replace with your SIP main account or subaccount)
- Authentication Password: Your SIP account's password
- Dial Plan: x+P (By default)
SIP Server
- Server Address: One of VoIP.ms multiple SERVERS, you can choose the one closest to your location
- Port: 5060 (Aditionally you could use 5080 or 42872)
Registration
- Server Address: Be sure that you use the same one you used at Server Address
- Port: 5060 (Aditionally you could use 5080 or 42872)
- Expiration (secs): 300
- Registration Freq (secs): 10
Outbound Proxy
- Server Address: Be sure that you use the same one you used at Server Address
- Port: 5060 (Aditionally you could use 5080 or 42872)
Backup Outbound Proxy
Leave these settings as they are by default
Audio
We strongly recommend to have set here only the audio codec(s) you have enabled in your SIP account's settings (preferrably only one). In case you need to have more than 1 Audio codec, it can be set as follows:
- Ringer Tone: 1 (or the one you prefer)
- Codec Priority 1: G.711u
- Codec Priority 2: G.729a/b
- Codec Priority 3: None
- Codec Priority 4: None
- Codec Priority 5: None
Signaling Settings
- Local SIP Port: 5060 (Aditionally you could use 5080 or 42872)
- Transport: UDP or TCP (Depending on your network's configuration)
You can leave all the other values as they are unless you actually need to specify them.
Scroll down and click on "Save" then you can go back to the "Status" tab, if all is correct, you will see your account as Registered
Using TLS/Encryption
The Vtech VCS754 is compatible with Call Encryption. However to use it, you need to change some settings in your device:
Ports for TLS
When you enable encryption calls from our system, the ports need to be changed to the encrypted ones. This is just adding " 1 " to the used port, leaving the available ones like 5061, 5081, 42873. Make the proper changes in your device's settings to have it working
Audio Section
Mark this "[]Enable Voice Encryption (SRTP)"
