Viking X-1605 Series Emergency Phones With HD Video
From VoIP.ms Wiki
The X-1605 Series of IP Video Emergency Phones are designed to provide HD video and reliable handsfree voice communication for SIP VoIP phone systems and service providers. The built-in IP video camera has H.264 video compression, low light sensitivity, a wide viewing angle of 126 degrees, and can output dual video streams of up to 1080p resolution.
The X-1605 emergency phones can dial programmable numbers and be programmed remotely via a built-in Web UI. On-board 2 Amp relay contacts are provided for activating door strikes or gate controllers. The X-1605 emergency phones will flash the blue LED during dialing and can automatically light the LED when the call is answered. All units are PoE class 2 powered.
For outdoor installations where the unit is exposed to precipitation or condensation, the X-1605 emergency phones are available with Enhanced Weather Protection (EWP). EWP products are designed to meet IP66 standards and may feature foam rubber gaskets, sealed connections, gel-filled butt connectors, as well as potted circuit boards. For more information on EWP, see DOD 859.
Contents |
Pre-requisists
- Be connected on the same LAN as the device.
- The X-Series Discovery Utility Software software to find the device. It can be downloaded directly through the Viking Product page. Here: https://vikingupgradeserver.com/_install/X-Discovery.zip.
- In your VoIP.ms Sub-Account configuration, you must select the codec G722 and G711u. G722 is used for internal calls to have an HD audio if you have this codec on your other devices that will reach internally this device. Example with an internal extension number. (You must have this codec selected on all your devices to make it work).
Programming
Find the device
- 1. To begin, install and launch the X-Series Discovery Utility software. This tool will detect X-1605 units within the same LAN and display their respective IP addresses.
- 2. Double-click on a unit to access its Web UI through your default browser.
- 3. Once you have identified the IP address, you can also access the Web UI using a smartphone browser for convenience.
Accessing the device by the Web UI
- 1. To access the UI, simply enter the X-1605's IP address into your browser's address bar. By default, HTTPS is used. If your browser indicates an insecure connection, click on the "Lock" icon near the address bar. You can then view the CA certificate and add it to the Certificate Store on your computer for secure access. If you're using the Viking X-Series Discovery Utility, double-clicking on the unit will attempt to log in with the default password.
- 2. Click [Login]
- For the initial login, use the following credentials:
- Username: admin
- Password: admin
- Upon logging in, you will be prompted to change the password to a non-default one for enhanced security.
- For the initial login, use the following credentials:
Configuring the X-1605 Network Settings
Account Settings
- 1. Click on the "VoIP" tab then Account on the left menu.
- 2. Where the Account Settings section
- 2.1 Phone Number/UserID: Enter your VoIP.ms sub-account SIP username.
- 2.2 Authentication ID: Enter your VoIP.ms sub-account SIP username.
- 2.3 Authenticated Password: Enter your VoIP.ms sub-account SIP username.
- 2.4 Caller ID: This should be the outbound caller ID number. See the notification below.
⚠️ IMPORTANT - Caller ID
- Entering outbound Caller ID Name, it must be in CAPITAL LETTERS. This will appears more clearly/visible on some devices.
- You must NOT use any special characters. They will not be displayed and it prevents potential outbound call issues.
- Do NOT exceed 15 characters. Traditional canadian providers will not show more than 15 characters. We suggest shrinking or adapt the name.
- Spaces are allowed in a caller ID name but count as a caracters. (do not exceed 15 chars. in total).
- 2.5 Registrar:port: Re enter the VoIPms POP Server.
- 2.6 Primary proxy:port: Re enter the VoIPms POP Server.
- 2.7 SIP Registration Expiry: Enter 60
- 2.8 SIP Registration Routing: Select SIP Registrar
- 3. Click [Apply]
Audio Settings
- 1. Click on the "VoIP" tab then Account on the left menu.
- 2. Where the Account Settings section
- 3. First Choice: Choose G.722 (You must ensure that the codec G722 is selected under your Sub-Account in order to have HD Calls for better audio clarity. And it must be choose on all your devices).
- 4. Second Choice: Choose G.711 ulaw.
- 5. Click [Apply]
Resources
- Vendor Product page: https://vikingelectronics.com/products/x-1605/
- Product Manual: https://vikingelectronics.com/wp-content/uploads/X-1605.pdf
- X-Series Discovery Utility Software: https://vikingupgradeserver.com/_install/X-Discovery.zip
