M5 Technologies Mediatrix 4102S
From VoIP.ms Wiki
(Difference between revisions)
| [checked revision] | [checked revision] |
(→Configure VoIP.ms POP) |
(→Configure VoIP.ms POP) |
||
| Line 158: | Line 158: | ||
= Configure VoIP.ms POP = | = Configure VoIP.ms POP = | ||
| + | == SIP == | ||
| + | == Servers == | ||
1. Go to '''SIP''' tab | 1. Go to '''SIP''' tab | ||
2. Then on '''"Servers"''' sub-menu. | 2. Then on '''"Servers"''' sub-menu. | ||
| Line 171: | Line 173: | ||
5. Click '''[Apply]''' | 5. Click '''[Apply]''' | ||
| + | |||
| + | == Registrations == | ||
| + | : 1. Go to '''SIP''' tab | ||
| + | : 2. Then on '''"Registrations"''' sub-menu. | ||
| + | : 3. On '''"Registrations''' section: | ||
| + | :: [[File:VoIPms_Media5Corp_Mediatrix_4102S_SIP_Registrations_RegConfig.png|550px]] | ||
= Restart the services = | = Restart the services = | ||
Revision as of 01:04, 23 April 2024
The Mediatrix 4102S serves as a VoIP adaptor facilitating the integration of analog telephones, faxes, and modems into SIP-based systems. This ATA streamlines deployment processes, enabling operators to swiftly set up highly secure environments. It empowers the seamless incorporation of cloud telephony services into branch offices and small to medium-sized businesses (SMBs).
Contents |
LED and Interface
LED description
| # | LED | Behavior | Condition |
|---|---|---|---|
| 1 | Ready | Green, steady ON | All lines are enabled (operational state) |
| OFF | All lines are disabled (operational state) | ||
| Blinking 1 cycle per 4 seconds, 75% duty | At least one line is enabled and at least one line is disabled (operational state) | ||
| 2 | In-Use | OFF | Lines idled and unlocked |
| Steady ON | Lines in use and unlocked | ||
| Steady yellow | Shutting down | ||
| Yellow, blinking yellow, 1 cycle per second, 50% duty | Locked | ||
| 3 | ETH | Green, blinking, variable rate | Network traffic |
| Green, steady ON | No network traffic | ||
| OFF | Not connected | ||
| 4 | Power | Amber, steady ON | Restart completed |
| OFF | Indicates that the unit is not connected | ||
| Blinking, 1 Hz, 50% duty | Restart in progress |
Interface Description
| # | Switch | Description |
|---|---|---|
| 4 | Reset / Default | Allows setting the unit to default (known) values. Refer to the deviceRESET/DEFAULT Button documentation. |
| # | Connnectors/Cards | Description |
|---|---|---|
| 1 | FXS card
with 2 FXS ports | 2 x RJ-11 connectors for analog phone or G3 fax machine. |
| 2 | LAN | 10/100 BaseT Ethernet RJ-45 connector for access to a LAN, WAN or computer. This ports is used by default for LAN connections. |
| 3 | WAN | A 10/100 BaseT Ethernet RJ-45 connector for access to a LAN, WAN or computer. This port is by default used for uplink / WAN connection. |
| 5 | RESET | External 12 Vdc 1.5 A power supply. |
IP Address Discovery or Configuration
The purpose of this section is to be able to contact the Mediatrix 4102's web interface to start with unit configuration. Once the physical connection is complete, you will need to power on the Mediatrix 4102 and find out the IP address it is using. The Mediatrix 4102's IP address can be set either dynamically or statically. The default behavior of the Mediatrix 4102 is to try to obtain a dynamic IP address through a DHCP server.
Connecting the Mediatrix Unit Using a DHCP Server
Before proceeding:
- 1. Ensure that your network connection is functional.
- 2. Use an IPv4 Network.
- 3. The IPv4 Network must have a DHCP server.
- 4. If your unit lacks an FXS port or you can't access the DHCP server's logs, utilize the Connecting the Mediatrix Unit Using a Static IP address procedure.
- Steps:
- 1. Wear an ESD wrist strap, ensuring it is properly grounded to bare skin.
- 2. Attach the ESD wrist strap end to an earth ground (an unpainted bare metal spot of a grounded equipment rack).
- 3. Ensure the circuit breakers of AC power sources powering the Mediatrix unit are switched OFF.
- 4. Connect the provided external Power Adapter to the DC connector of the Mediatrix unit and plug it into an appropriate AC electrical outlet.
- 5. Connect a 10/100 BaseT Ethernet RJ-45 cable into the WAN connector of the Mediatrix unit.
- 6. Connect the other end of the cable to a router/switch connected to your network.
- 7. Validate the installation.
- 8. Turn ON the AC power sources powering the Mediatrix unit at the circuit breaker.
Note: If condensation occurs when the unit is brought from a cold to a warm environment, wait for one hour before connecting the power cord. If you have an FXS port, dial *#*0 to obtain the IP address or consult the DHCP server's logs.
Result: The Power LED on the unit will flash during the DHCP server query and become solid once it successfully acquires an IP address. You can now use the DHCP IP address to access your unit's management interface.
Default Static IP Address Configuration
- If there is no DHCP server in your network, configuring the IP address statically is necessary.
- 1. Using a 10/100 Hub and two 10/100 BaseT Ethernet RJ-45 straight cables, connect both cables to the Hub. One cable should be connected to the WAN connector, and the other should link the computer to the Hub.
- 2. Reconfigure your computer's IP address to 192.168.0.10 and set the Subnet Mask to 255.255.255.0. Restart your computer.
- 3. Power on the Mediatrix 4102 by connecting the power cord's other end to an electrical outlet. Ensure the electrical outlet is installed near the Mediatrix 4102 for easy access.
- 4. Insert a small, unbent paper clip into the Reset/Default hole located at the rear of the Mediatrix 4102. The Power LED will begin blinking, and after a few seconds, all LEDs will start blinking. Release the paper clip after all LEDs start blinking but before they stop blinking (between 7-11 seconds). This action constitutes a partial reset. After a partial reset, the Mediatrix 4102 will use the default IP address 192.168.0.1/24. Refer to the Hardware Configuration Guide, Chapter Powering on the Mediatrix 4102, for detailed instructions on the partial reset procedure.
- 5. Proceed to access the Mediatrix 4102 web interface.
Access the Mediatrix 4102S Web Interface
- 1. In your web browser’s address field, type the IP address of the Mediatrix 4102:
- http://<IP address of WAN port>
- [x] obtained from the DHCP server, or
- [x] obtained in “Default Static IP Address Configuration” on page 2 (192.168.0.1)
- http://<IP address of WAN port>
2. Enter the user name public and no password. You can also use the following values:
- - User Name: admin
- - Password: administrator
- The Login page opens:
3. Click Login.
- The System Information web page displays.
Configure VoIP.ms POP
SIP
Servers
1. Go to SIP tab 2. Then on "Servers" sub-menu. 3. On "Default Servers section:
- 1. Registrar host: Enter the VoIP.ms POP server you want to use. eg: montreal3.voip.ms
- 2. Proxy host": Re-enter the VoIP.ms POP server you have entered on Registrar host. eg: montreal3.voip.ms
-
4. On "Keep-Alive" section:
- 1. Keep-Alive Method: Choose: SIP OPTIONS
- 2. Keep-Alive Interval (s): Enter 30.
-
5. Click [Apply]
Registrations
- 1. Go to SIP tab
- 2. Then on "Registrations" sub-menu.
- 3. On "Registrations section:
-
Restart the services
- After setting the VoIP.ms POP in the SIP --> Servers sub-menu a services restart is required in order to correctly apply the new parameters:
- Click on the "restart required services" link at the top of the page
Enabling the telephony ports registration
- 1. Go to SIP
- 2. Go to Registrations sub-menu
- 3. For each analog port to register:
- 4. Username column, enter the associated VoIP.ms account/sub-account username, example: ######_SubAccount
- 5. "Friendly Name" column: Enter the outbound callerID Name. See the information below
Friendly Name - IMPORTANT
- Entering outbound Caller ID Name, it must be in CAPITAL LETTERS. This will appears more clearly/visible on some devices.
- You must NOT use any special characters. They will not be displayed and it prevents potential outbound call issues.
- Do NOT exceed 15 characters. Traditional canadian providers will not show more than 15 characters. We suggest shrinking or adapt the name.
- Spaces are allowed in a caller ID name but count as a characters. (do not exceed 15 chars. in total).
- 6. Register column, select Enable from the drop-down list
- 7. Click [Apply]
Ressources
- Product Page: https://www.m5t.com/pages/mediatrix-4102s-en
- Data Sheet: https://www.m5t.com/wp-content/uploads/Mediatrix_4102_datasheet.pdf
- Hardware Installation Guide
