Konftel 300Wx IP

From VoIP.ms Wiki

[checked revision]

---

Revision as of 19:39, 6 February 2020

The wireless conference phone Konftel 300Wx allows you to hold meetings wherever is convenient for you – without worrying about network and power outlets. The wireless DECT technology is both reliable and secure. Choose a base station to suit your company's telephony environment, SIP or analog, or connect to an installed DECT system.

The rechargeable battery ensures more than 60 call hours, so you can talk for a full work week without recharging!

Contents 1 Configuring a line 1.1 Accessing The Web Interface 1.2 Adding a SIP Server 1.3 Adding an Extension 2 Configuring with TLS / Encryption 2.1 Adding a SIP Server with TLS 2.2 Adding an Extension with a TLS server 3 Verifying its status

Configuring a line

Accessing The Web Interface

In order to configure the 300WX device to be used along with our service, it is required to access it's web interface settings. For this, the IP address of the device must be acquired.

To perform this click on the menu and navigate to: " Status " , then select: " Network ". It should read back something as: " 192.168.0.1

Once you have the IP address please open a web browser of your preference and at the URL bar enter the IP address you got by prepending: " http:// " and access it. Once accessed, you'll be prompted to authenticate.

Profile: " admin " Password: " admin "

Adding a SIP Server

Once logged in, please navigate to: Server on the left menu and click Add Server.

Set up the account you will be using, with the following values

• Server Alias: An alias name for your server (It can be the server's name)
• NAT Adaption: Enabled
• Registrar: One of VoIP.ms multiple servers, you can choose the one closest to your location
• Outbound Proxy: Set the same server you set at Registrar
• Reregistrarion time (s): 300
• SIP Transport: TCP
• Keep Alive: Enabled
• Codec Priority: Here leave only the codecs you have enabled in your SIP account's settings

Then click "Save" and go to "Extensions"

Once done, click the Save and go to the "Extensions" menu on the left

Adding an Extension

Here, click on "Add extension" and complete the fields with your sub account's information:

• Extension: 100000 (replace with your SIP main account or subaccount)
• Authentication Username: 100000 (replace with your SIP main account or subaccount)
• Authentication password: Your SIP account's password
• Server: The server you created on a previous step (Since you can have more than one server, be sure that is the one you need to use)

On the right, you will see listed the handsets available for your IP DECT, select the one you will use with the current extension (as marked within the image below)

Click on "Save" after you are done.

Configuring with TLS / Encryption

NOTE: This section is optional. It explains in detail how to use encrypted traffic in the device. If you are not certain about how encrypted traffic works, or the benefits of encrypting SIP traffic, please contact technical support for more information.

The Konftel 300Wx is compatible with TLS, however, some settings need to be adjusted to have it working. This section will be assuming that your SIP account is already enabled to use TLS, if you have not enabled it yet, please follow these instructions before going further:

For more information on how to enable encrypted traffic for the main account, please click on Main account or more information on how to enable encrypted traffic for the sub-account sub account

Adding a SIP Server with TLS

Once logged in, please navigate to: Server on the left menu and click Add Server.

Set up the account you will be using, with the following values

• Server Alias: An alias name for your server (It can be the server's name)
• NAT Adaption: Enabled
• Registrar: One of VoIP.ms multiple servers, you can choose the one closest to your location
• Outbound Proxy: Set the same server you set at Registrar
• Reregistrarion time (s): 300
• SIP Transport: TCP
• Keep Alive: Enabled
• Codec Priority: Here leave only the codecs you have enabled in your SIP account's settings
• Sercure RTP: Enabled
• Secure RTP Auth: Enabled

Then click "Save" and go to "Extensions"

Once done, click the Save and go to the "Extensions" menu on the left

Adding an Extension with a TLS server

Here, click on "Add extension" and complete the fields with your sub account's information:

• Extension: 100000 (replace with your SIP main account or subaccount)
• Authentication Username: 100000 (replace with your SIP main account or subaccount)
• Authentication password: Your SIP account's password
• Server: The server you created on a previous step (Since you can have more than one server, be sure that is the one you need to use)

On the right, you will see listed the handsets available for your IP DECT, select the one you will use with the current extension (as marked within the image below)

Click on "Save" after you are done.

Verifying its status

If all was properly set and your device has connectivity, you will be registered. You can confirm this on the Status section on your device (besides your VoIP.ms customer portal)

Go to Extensions and you should see information similar to the one below