Beronet
From VoIP.ms Wiki
| [draft revision] | [draft revision] |
| Line 22: | Line 22: | ||
You will need the following settings from your VoIP.ms account. | You will need the following settings from your VoIP.ms account. | ||
| - | - SIP username from your sub account | + | - SIP outbound proxy: |
| - | - Your sub account password | + | - SIP registrar: Your VoIP.ms server |
| - | + | - SIP domain: Your VoIP.ms server | |
| + | - User: SIP username from your sub account | ||
| + | - Secret: Your sub account password | ||
- The SIP Transport-Procol is '''UDP''' | - The SIP Transport-Procol is '''UDP''' | ||
| Line 57: | Line 59: | ||
[[File:BeroNET_SIP_Config_Register.png|780px|border]] | [[File:BeroNET_SIP_Config_Register.png|780px|border]] | ||
| + | |||
| + | |||
| + | Advanced SIP account Settings | ||
| + | Under the menu "more" you don't have to change anything because the default settings of the gateway are ok. Nevertheless I will explain some settings because they are important to understand if something has to be changed. | ||
| + | |||
| + | The SIP-Header "From-Display" should contain the outgoing CalledID and has to be changed to "new_source" while the From_User_Part has to be changed to account_username. | ||
| + | |||
| + | |||
| + | |||
| + | From User Part = account_username | ||
| + | |||
| + | From Display Part = new_source | ||
| + | |||
| + | |||
| + | |||
| + | Dialplan_Source is set by default to from_display and don't have to be changed. | ||
| + | |||
| + | Dialplan_Source = from_display | ||
| + | |||
| + | |||
| + | |||
| + | Finally we have to set the Country and City Code, as well as the International prefix, for instance the settings for Germany Berlin are: | ||
| + | |||
| + | '''International Code: 011''' ''(without trailing 00)'' | ||
| + | '''National Code: 1''' ''(without trailing 0)'' | ||
| + | '''International prefix 00''' | ||
| + | |||
| + | |||
| + | Furthermore you can choose the Destination and Source Number Format. Deafult is 00 (int) (nat) (num) | ||
Revision as of 15:00, 30 August 2019
beroNet is Europe's leading manufacturer of ISDN, Analog, Hybrid and GSM VoIP access technologies. The following section describes the configuration to configure a VoIP.ms SIP Trunk on a beroNet VoIP gateway.
Contents |
To start, you will need to validate the version of your beroNet Gateway, it's need to be at the firmware version 16.15 or higher.
This example are base on an ISDN-PBX with PRI/BRI interfaces who is connected to a BeroNet gateway on a site and the other one on another site, we will explain you how to link a VoIP.ms SIP-Trunk.
(( Configuration Steps:
1. Hardware Settings
2. ISDN Portgroup configuration
3. General SIP Settings
4. Create a SIP Account
5. Dialplan configuration
))
Connection Settings SIP Trunk
You will need the following settings from your VoIP.ms account.
- SIP outbound proxy: - SIP registrar: Your VoIP.ms server - SIP domain: Your VoIP.ms server - User: SIP username from your sub account - Secret: Your sub account password - The SIP Transport-Procol is UDP
SIP General Settings
To be able to connect your SIP Account, you will need to create a SIP Trunk. To do so, go to the top navigation menu and clic on "SIP+".
Once you are at the "SIP CONFIGURATION" page, you will need to add a new trunk by clicking on "Add"
On the top menu SIP, "SIP General Options" you can modify general SIP-Account Settings.
Depending on how/where you are going to use the beroNet gateway, you will need to add "port forwarding rules" on your Route for the SIP Bindport 5060 and the Audion RTP Range 10000-20000.
To start, please login into your BeroNET VoIP Appliance.
SIP Account
When the information is entered, you will need to check the box Register under the option SIP Configuration.
Advanced SIP account Settings
Under the menu "more" you don't have to change anything because the default settings of the gateway are ok. Nevertheless I will explain some settings because they are important to understand if something has to be changed.
The SIP-Header "From-Display" should contain the outgoing CalledID and has to be changed to "new_source" while the From_User_Part has to be changed to account_username.
From User Part = account_username
From Display Part = new_source
Dialplan_Source is set by default to from_display and don't have to be changed.
Dialplan_Source = from_display
Finally we have to set the Country and City Code, as well as the International prefix, for instance the settings for Germany Berlin are:
International Code: 011 (without trailing 00) National Code: 1 (without trailing 0) International prefix 00
Furthermore you can choose the Destination and Source Number Format. Deafult is 00 (int) (nat) (num)
Hardware Settings
ISDN Port Groups
Dialplan configuration
