TalkSwitch
From VoIP.ms Wiki
(Difference between revisions)
| [draft revision] | [draft revision] |
(→Username and Password) |
90210chris (Talk | contribs) |
||
| Line 3: | Line 3: | ||
This guide will show you how to set up VoIP.ms VoIP service. | This guide will show you how to set up VoIP.ms VoIP service. | ||
| - | When you | + | When you open an account with VoIP.ms, we will provide you with account credentials information. Use this information to set up the service provider profile and VoIP numbers on your TalkSwitch system. |
''Setting up a service provider profile'' | ''Setting up a service provider profile'' | ||
| Line 22: | Line 22: | ||
Check Register with authentication username. | Check Register with authentication username. | ||
Check Enable NAT Keep alives (You can keep the default NAT settings) | Check Enable NAT Keep alives (You can keep the default NAT settings) | ||
| - | Codec Options: Here make sure to select only the codec supported for VoIP.ms (g.729 and g.711u). And if you have enough | + | Codec Options: Here make sure to select only the codec supported for VoIP.ms (g.729 and g.711u). And if you have enough bandwidth you should select the g.711u as Preferred codec. |
[[File:Image002.png]] | [[File:Image002.png]] | ||
| Line 39: | Line 39: | ||
*Select one of the empty voip number slots and then check the '''Activate VoIP number''' | *Select one of the empty voip number slots and then check the '''Activate VoIP number''' | ||
| - | *'''Select a VoIP profile''': Here select the profile create for VoIP.ms | + | *'''Select a VoIP profile''': Here select the profile to create for VoIP.ms |
| - | '''''The record for your main account sip userID as | + | '''''The record for your main account sip userID as shown in the screen, this is required as this section sends the correct information required from our servers on the INVITES:FROM which will be the userid, if you don't add this record the Talkswitch will be sending the number (DID set) instead and this will result in continuous 'deregistrations', registration dropping.''''' |
===Username and Password=== | ===Username and Password=== | ||
| Line 47: | Line 47: | ||
*'''User/Account''': 100000 (Replace with your 6 digit Main SIP Account User ID or Sub Account username, i.e. 123456 or 123456_sub) | *'''User/Account''': 100000 (Replace with your 6 digit Main SIP Account User ID or Sub Account username, i.e. 123456 or 123456_sub) | ||
| - | *'''Password''': (the password for your account. If you're using the main account this is the same you use to login | + | *'''Password''': (the password for your account. If you're using the main account this is the same you use to login to your Customer Portal, unless you change the password, if using a sub account you'll notice each sub account has their own password) |
| - | '''Note''' You can only use the main account for outgoing calls, this is due to Talkswitch system | + | '''Note''' You can only use the main account for outgoing calls, this is due to the Talkswitch system not supporting |
the Underscore on the sub accounts. | the Underscore on the sub accounts. | ||
| Line 58: | Line 58: | ||
[[File:Voip number inbound (3).jpg|800px]] | [[File:Voip number inbound (3).jpg|800px]] | ||
| - | Here you can set the callerID number that you want (or your DID number if you want to receive incoming calls), you need to enter the number filling the 3 fields. | + | Here you can set the callerID number that you want (or your DID number if you want to receive incoming calls), you need to enter the number filling in the 3 fields. |
*'''Country Code''': 1 | *'''Country Code''': 1 | ||
*'''City or area code''': 555 | *'''City or area code''': 555 | ||
| Line 67: | Line 67: | ||
'''Note:''' If you are planning to use more than 1 number with us, as you may know the Talkswitch requires you to add different accounts for | '''Note:''' If you are planning to use more than 1 number with us, as you may know the Talkswitch requires you to add different accounts for | ||
| - | incoming | + | incoming. You can use the sub accounts in this section, however on the customer portal you will need to set the sub accounts for IP |
| - | authentication | + | authentication and you will have to contact us in order to set all the sub accounts to the same IP address (currently the configuration |
| - | will require different IP | + | will require different IP addresses). |
Revision as of 20:05, 28 August 2014
Contents |
Configuring TalkSwitch for VoIP.ms VoIP Service
This guide will show you how to set up VoIP.ms VoIP service.
When you open an account with VoIP.ms, we will provide you with account credentials information. Use this information to set up the service provider profile and VoIP numbers on your TalkSwitch system.
Setting up a service provider profile
1. Select the VoIP Configuration page.
2. Select a Profile (SP 1 to SP 4) that you wish to assign for FortiCall.
3. Select the Activate Profile checkbox.
4. Under Service Provider select Manual Setup.
5. Click the Update Configuration button. The essential settings will be completed automatically.
Disable public IP address substitution leave this unchecked. Check Register with authentication username. Check Enable NAT Keep alives (You can keep the default NAT settings) Codec Options: Here make sure to select only the codec supported for VoIP.ms (g.729 and g.711u). And if you have enough bandwidth you should select the g.711u as Preferred codec.
Provisioning Details
- Proxy Server name: server.voip.ms (one of the voip.ms servers, e.g. atlanta.voip.ms)
- Registrar server name: same as above
- Outbound proxy: same as above
- Realm/domain: same as above
Configuring Outgoing calls with VoIP.ms
- Select the VoIP Numbers page
.jpg)
- Select one of the empty voip number slots and then check the Activate VoIP number
- Select a VoIP profile: Here select the profile to create for VoIP.ms
The record for your main account sip userID as shown in the screen, this is required as this section sends the correct information required from our servers on the INVITES:FROM which will be the userid, if you don't add this record the Talkswitch will be sending the number (DID set) instead and this will result in continuous 'deregistrations', registration dropping.
Username and Password
- User/Account: 100000 (Replace with your 6 digit Main SIP Account User ID or Sub Account username, i.e. 123456 or 123456_sub)
- Password: (the password for your account. If you're using the main account this is the same you use to login to your Customer Portal, unless you change the password, if using a sub account you'll notice each sub account has their own password)
Note You can only use the main account for outgoing calls, this is due to the Talkswitch system not supporting the Underscore on the sub accounts.
Configuring Incoming calls with VoIP.ms
Note: You don't need to purchase a DID number for outgoing calls. The VoIP number is used as your CallerID number.
.jpg)
Here you can set the callerID number that you want (or your DID number if you want to receive incoming calls), you need to enter the number filling in the 3 fields.
- Country Code: 1
- City or area code: 555
- Number: 4443322
Note: If you are planning to use more than 1 number with us, as you may know the Talkswitch requires you to add different accounts for incoming. You can use the sub accounts in this section, however on the customer portal you will need to set the sub accounts for IP authentication and you will have to contact us in order to set all the sub accounts to the same IP address (currently the configuration will require different IP addresses).
