Grandstream HT802v2
From VoIP.ms Wiki
(Difference between revisions)
| [checked revision] | [checked revision] |
(→General Settings (FXS PORT1)) |
(→General Settings (FXS PORT1)) |
||
| Line 26: | Line 26: | ||
=General Settings (FXS PORT1)= | =General Settings (FXS PORT1)= | ||
| - | + | ==Account Registration== | |
:* '''Account Active:''' ✅ Checked | :* '''Account Active:''' ✅ Checked | ||
:* '''Primary SIP Server''': popserver.voip.ms (or your nearest VoIP.ms POP) | :* '''Primary SIP Server''': popserver.voip.ms (or your nearest VoIP.ms POP) | ||
| Line 38: | Line 38: | ||
:: [[File:HT802v2_FXS1_General_Settings_AccountRegistration.png|600px]] | :: [[File:HT802v2_FXS1_General_Settings_AccountRegistration.png|600px]] | ||
| - | + | ==Network Settings== | |
:* '''DNS Mode''': A Record | :* '''DNS Mode''': A Record | ||
:* '''NAT Traversal''' Keep-Alive | :* '''NAT Traversal''' Keep-Alive | ||
: Click '''Save and Apply'''. | : Click '''Save and Apply'''. | ||
| - | |||
:: [[File:HT802v2_FXS1_General_Settings_NetworkSettings.png|600px]] | :: [[File:HT802v2_FXS1_General_Settings_NetworkSettings.png|600px]] | ||
Revision as of 17:39, 15 August 2025
📖 VoIP.ms Grandstream HT802 V2 Setup Guide
Contents |
Overview
This guide walks you through configuring a Grandstream HT802 V2 with VoIP.ms. It supports: - Voice service - Fax (T.38 or G.711 pass-through)
Requirements
- Grandstream HT802 V2
- Latest firmware installed (Grandstream site) (We you use firmware version 1.0.5.7 or later.)
- VoIP.ms account with a configured DID and a sub-account
- Internet access via Ethernet
- Phone or fax device connected to FXS Port 1
Logging into the Web Interface
- Connect the HT802 to your network and power it on.
- Pick up the connected phone, dial:
- ***02 (Star Star Star 0 2)
The ATA will read its IP address. Open a browser and go to that IP (e.g., http://192.168.1.50).
- Login
- Username: admin
- Password: found on device label (or as set by you)
General Settings (FXS PORT1)
Account Registration
- Account Active: ✅ Checked
- Primary SIP Server: popserver.voip.ms (or your nearest VoIP.ms POP)
- Prefer Primary SIP Server Yes
- Outbound Proxy popserver.voip.ms (Same as the Primary SIP Server)
- Backup Outbound Proxy This is optional you can use a different PoP on a different location.
- Prefer Primary Outbound Proxy: Check the box, only if you entered a backup Outbound Proxy
- SIP User ID Your VoIP.ms sub-account username
- SIP Authenticate ID Same as SIP User ID
- SIP Authentication Password Your sub-account password
Network Settings
- DNS Mode: A Record
- NAT Traversal Keep-Alive
- Click Save and Apply.
-
SIP Settings Tab
- Register Expiration: 120 seconds
- Enable SIP OPTIONS Keep Alive: Yes
- Local SIP Port: 5060 (change if multiple ATAs)
- Disable extra headers:
- Privacy Header → No
- P-Preferred-Identity Header → No
- P-Access-Network-Info → No
- P-Emergency-Info → No
Codec Settings Tab
- Preferred Vocoder (in all sessions): G722, (G.711 μ-law) then set G711 for the rest.
Advanced Settings
- Check SIP User ID for Incoming INVITE: Enabled
- Allow incoming SIP messages from SIP proxy only: Enabled
Faxing
- Ensure options like Enable‑Call‑Waiting, Caller‑ID, and Tone are unchecked — avoiding disruptions during fax sessions.
- Security Settings: Enable Allow incoming packets from SIP proxy only to restrict access to VoIP.ms servers.
- Under Call Settings
- Disable Local Call Features: Yes
- Enable-Call-Waiting: uncheck
- Enable-Call-Waiting-Caller-ID: uncheck
- Enable-Call-Waiting-Tone: uncheck
- Under Call Features Settings:
- Set Enable Local Call Features No to prevent unintended feature code usage via the fax machine.
- Under Codec Settings:
- Fax Mode: T.38 (if you are using it for faxing with a VoIP.ms FAX POP server)
- T.38 Max Bit Rate: 14400 bps
- Jitter Buffer: Fixed, High
- Under Analog Signal Line Configuration
- Enable Line Echo Canceller (LEC) → Check
Testing
- Reboot the ATA after applying settings.
- Check Status tab → Registration should be Yes.
- Dial: 4443 for a Voice Echo Test.
