|
|
| (2 intermediate revisions not shown) |
| Line 1: |
Line 1: |
| - | 📖 VoIP.ms Grandstream HT802 V2 Setup Guide
| + | #REDIRECT [[Grandstream_HT802v2]] |
| - | | + | |
| - | =Overview=
| + | |
| - | This guide walks you through configuring a Grandstream HT802 V2 with VoIP.ms.
| + | |
| - | It supports:
| + | |
| - | - Voice service
| + | |
| - | - Fax (T.38 or G.711 pass-through)
| + | |
| - | | + | |
| - | =Requirements=
| + | |
| - | :* Grandstream HT802 V2
| + | |
| - | :* Latest firmware installed (check Grandstream site)
| + | |
| - | :* VoIP.ms account with a configured DID and a sub-account
| + | |
| - | :* Internet access via Ethernet
| + | |
| - | :* Phone or fax device connected to FXS Port 1
| + | |
| - | | + | |
| - | =Logging into the Web Interface=
| + | |
| - | : Connect the HT802 to your network and power it on.
| + | |
| - | :* Pick up the connected phone, dial:
| + | |
| - | :* ***02 (Star Star Star 0 2)
| + | |
| - | | + | |
| - | The ATA will read its IP address.
| + | |
| - | Open a browser and go to that IP (e.g., http://192.168.1.50).
| + | |
| - | : Login
| + | |
| - | :* Username: admin
| + | |
| - | :* Password: found on device label (or as set by you)
| + | |
| - | | + | |
| - | =General Settings (FXS PORT1)=
| + | |
| - | :* '''Account Active:''' ✅ Checked
| + | |
| - | :* '''Primary SIP Server''': popserver.voip.ms (or your nearest VoIP.ms POP)
| + | |
| - | :* '''Failover SIP Server''' Optional: backup POP
| + | |
| - | :* '''Prefer Primary SIP Server''' No
| + | |
| - | :* '''SIP User ID''' Your VoIP.ms sub-account number
| + | |
| - | :* '''SIP Authenticate ID''' Same as SIP User ID
| + | |
| - | :* '''SIP Authentication Password''' Your VoIP.ms SIP password
| + | |
| - | :* '''NAT Traversal''' Keep-Alive (recommended)
| + | |
| - | : Click '''Save and Apply'''.
| + | |
| - | | + | |
| - | =SIP Settings Tab=
| + | |
| - | :* '''Register Expiration''': 120 seconds
| + | |
| - | :* '''Enable SIP OPTIONS Keep Alive''': Yes
| + | |
| - | :* Local SIP Port: 5060 (change if multiple ATAs)
| + | |
| - | : Disable extra headers:
| + | |
| - | :* '''Privacy Header''' → No
| + | |
| - | :* '''P-Preferred-Identity Header''' → No
| + | |
| - | :* '''P-Access-Network-Info''' → No
| + | |
| - | :* '''P-Emergency-Info''' → No
| + | |
| - | | + | |
| - | =Codec Settings Tab=
| + | |
| - | : '''Preferred Vocoder''' (in all sessions): G722, (G.711 μ-law) then set G711 for the rest.
| + | |
| - | | + | |
| - | =Advanced Settings=
| + | |
| - | | + | |
| - | : '''Allow incoming SIP messages from SIP proxy only''': Enabled
| + | |
| - | : '''Disable Local Call Features''': Yes
| + | |
| - | | + | |
| - | | + | |
| - | | + | |
| - | ==Faxing==
| + | |
| - | : '''Fax Mode''': T.38 (if you are using it for faxing with a VoIP.ms FAX POP server)
| + | |
| - | : '''T.38 Max Bit Rat'''e: 14400 bps
| + | |
| - | : '''Jitter Buffer''': Fixed, High
| + | |
| - | | + | |
| - | =Testing=
| + | |
| - | : Reboot the ATA after applying settings.
| + | |
| - | : Check '''Status tab''' → Registration should be '''Yes'''.
| + | |
| - | : Dial: 4443 for a Voice Echo Test.
| + | |
