Poly VVX-D230
From VoIP.ms Wiki
(Difference between revisions)
| [draft revision] | [draft revision] |
(Created page with "The VVX-D230's base can control ten DECT handsets Aimed at small business users, the Poly (Polycom, Obahai) VVX-D230 is a DECT [[IP Phones|...") |
m (→Configuration) |
||
| (4 intermediate revisions not shown) | |||
| Line 1: | Line 1: | ||
| - | [[Image:Poly- | + | [[Image:Poly VVX-D230 base.png|thumb|The VVX-D230's base can control ten DECT handsets]] |
| - | Aimed at small business users, the Poly (Polycom, Obahai) VVX-D230 is a DECT [[IP Phones|SIP phone]] with support for up to ten cordless handsets — including the one handset which is packaged with the base. | + | Aimed at small business users, the Poly (Polycom, Obahai) '''VVX-D230''' is a DECT [[IP Phones|SIP phone]] with support for up to ten cordless handsets — including the one handset which is packaged with the base. |
This system (OBAHAI/VVXD230) is intended to complement the [[Polycom VVX 300, 400, etc|VVX-series]] desk phones and the [[Poly Trio 8800]] conference room speakerphone. | This system (OBAHAI/VVXD230) is intended to complement the [[Polycom VVX 300, 400, etc|VVX-series]] desk phones and the [[Poly Trio 8800]] conference room speakerphone. | ||
| Line 6: | Line 6: | ||
==Configuration== | ==Configuration== | ||
# If the cordless handsets are not already paired to the base, press and hold the 'find' button on the base for at least five seconds. Then, from the handset, go to Menu→Settings→Registration→Register. | # If the cordless handsets are not already paired to the base, press and hold the 'find' button on the base for at least five seconds. Then, from the handset, go to Menu→Settings→Registration→Register. | ||
| - | # Configuration of the system is done via a web interface. From | + | # Configuration of the system is done via a web interface. From the first paired handset, go to Menu→Settings→Basestation Info to obtain the IPv4 address of the base. |
# Open a web browser to this address and log in with username 'admin' and default password 'admin'. | # Open a web browser to this address and log in with username 'admin' and default password 'admin'. | ||
| - | From the "Setup Wizard" page, change the following parameters (changes will not be applied until you save them and reboot the device). Be sure to uncheck the "default" check box for each item you intend to modify: | + | <br clear="all"> |
| - | *LocalTimeZone - set to your local time zone, for instance GMT-5:00 for (Eastern Time). Factory default is GMT-8:00 (Pacific Time, California). | + | [[Image:Poly VVX-D230 Wizard.png]] |
| - | *ITSP A SIPProxyServer - atlanta.voip.ms (or one of the other multiple [[servers]] - this must match the same server as your [[DID Troubleshooting|DID]] configuration). | + | |
| - | *ITSP A DigitMap - (optional) (1xxxxxxxxxx|<1555>[2-9]xxxxxxS3|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.) (as an example, replacing 1-555 with your local area code) will enable both 7 and 10-digit dial for North American numbers. See the manufacturer's technical reference manual for details of the syntax. | + | '''From the "Setup Wizard" page''', change the following parameters (changes will not be applied until you save them and reboot the device). Be sure to uncheck the "default" check box for each item you intend to modify: |
| - | *Phone1 PrimaryLine - "SP1 service" | + | *'''LocalTimeZone''' - set to your local time zone, for instance GMT-5:00 for (Eastern Time). Factory default is GMT-8:00 (Pacific Time, California). |
| - | *SP1 ITSP Profile - A | + | *'''ITSP A SIPProxyServer''' - atlanta.voip.ms (or one of the other multiple [[servers]] - this must match the same server as your [[DID Troubleshooting|DID]] configuration). |
| - | *SP1 AuthUserName - 123456_1 (your voip.ms user number and a [[Sub Accounts|subaccount]] number, in this example user #123456 subaccount #1 | + | *'''ITSP A DigitMap''' - (optional) (1xxxxxxxxxx|<1555>[2-9]xxxxxxS3|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.) (as an example, replacing 1-555 with your local area code) will enable both 7 and 10-digit dial for North American numbers. See the manufacturer's technical reference manual for details of the syntax. |
| - | *SP1 AuthPassword - the password associated with your voip.ms subsccount | + | *'''Phone1 PrimaryLine''' - "SP1 service" |
| + | *'''SP1 ITSP Profile''' - A | ||
| + | *'''SP1 AuthUserName''' - 123456_1 (your voip.ms user number and a [[Sub Accounts|subaccount]] number, in this example user #123456 subaccount #1 | ||
| + | *'''SP1 AuthPassword''' - the password associated with your voip.ms subsccount | ||
If you have additional virtual lines, repeat the same configuration steps for each subaccount using SP2, SP3... up to a maximum of eight lines and ten handsets. | If you have additional virtual lines, repeat the same configuration steps for each subaccount using SP2, SP3... up to a maximum of eight lines and ten handsets. | ||
| - | From the "SP1 Service" page, change the following settings for the first virtual "line" (the others will be similar): | + | <br clear="all"> |
| - | *X_DisplayNumber - A short text string identifying this line on the local handset screen. Typically the seven-digit NXX-XXXX local number, although any value will do. | + | [[Image:Poly VVX-D230 SP1.png]] |
| - | *X_AcceptSipFromRegistrarOnly - YES (to keep [[Sip Scanner Ghost Calls|spurious]] calls out) | + | |
| - | *X_KeepAliveEnable - YES (if you are behind NAT) | + | '''From the "SP1 Service" page''', change the following settings for the first virtual "line" (the others will be similar): |
| - | *X_KeepAliveExpires - 180 (three minutes) is reasonable | + | *'''X_DisplayNumber''' - A short text string identifying this line on the local handset screen. Typically the seven-digit NXX-XXXX local number, although any value will do. |
| - | *DirectoryNumber - NPA-NXX-XXXX, the directory number associated with this line | + | *'''X_InboundCallRoute''' - DT1,DT2,DT3 (if this number is to ring to the first three extensions, for example). The default (DT1) rings only to the first extension on inbound calls. |
| - | *AuthUserName, AuthPassword - should already be set from the "Setup Wizard" above; if not, set them here. | + | *'''X_AcceptSipFromRegistrarOnly''' - YES (to keep [[Sip Scanner Ghost Calls|spurious]] calls out) |
| - | *CallerIDName - your name (15 alphanumeric chars max, no punctuation but spaces are allowed) as you want it to appear on [[Caller ID]] for outbound calls. | + | *'''X_KeepAliveEnable''' - YES (if you are behind NAT) |
| - | *X_CheckVoiceMailNumber - *97 | + | *'''X_KeepAliveExpires''' - 180 (three minutes) is reasonable |
| - | *MessageWaiting - YES | + | *'''DirectoryNumber''' - NPA-NXX-XXXX, the directory number associated with this line |
| + | *'''AuthUserName''', '''AuthPassword''' - should already be set from the "Setup Wizard" above; if not, set them here. | ||
| + | *'''CallerIDName''' - your name (15 alphanumeric chars max, no punctuation but spaces are allowed) as you want it to appear on [[Caller ID]] for outbound calls. | ||
| + | *'''X_CheckVoiceMailNumber''' - *97 | ||
| + | *'''MessageWaiting''' - YES | ||
Save everything before leaving each page of the setup. When you are finished making changes, reboot the device. | Save everything before leaving each page of the setup. When you are finished making changes, reboot the device. | ||
| Line 34: | Line 41: | ||
Try a test call, such as the [[Dialing Codes|echo test]] (press [4] [4] [4] [3] and the [green] button). You should hear your own voice played back just as it was received. | Try a test call, such as the [[Dialing Codes|echo test]] (press [4] [4] [4] [3] and the [green] button). You should hear your own voice played back just as it was received. | ||
| - | ==See | + | ==See also== |
* [[Polycom VVX 300, 400, etc|VVX-series]] | * [[Polycom VVX 300, 400, etc|VVX-series]] | ||
* [[Poly Trio 8800]] | * [[Poly Trio 8800]] | ||
Latest revision as of 01:33, 7 December 2023
Aimed at small business users, the Poly (Polycom, Obahai) VVX-D230 is a DECT SIP phone with support for up to ten cordless handsets — including the one handset which is packaged with the base.
This system (OBAHAI/VVXD230) is intended to complement the VVX-series desk phones and the Poly Trio 8800 conference room speakerphone.
Configuration
- If the cordless handsets are not already paired to the base, press and hold the 'find' button on the base for at least five seconds. Then, from the handset, go to Menu→Settings→Registration→Register.
- Configuration of the system is done via a web interface. From the first paired handset, go to Menu→Settings→Basestation Info to obtain the IPv4 address of the base.
- Open a web browser to this address and log in with username 'admin' and default password 'admin'.
From the "Setup Wizard" page, change the following parameters (changes will not be applied until you save them and reboot the device). Be sure to uncheck the "default" check box for each item you intend to modify:
- LocalTimeZone - set to your local time zone, for instance GMT-5:00 for (Eastern Time). Factory default is GMT-8:00 (Pacific Time, California).
- ITSP A SIPProxyServer - atlanta.voip.ms (or one of the other multiple servers - this must match the same server as your DID configuration).
- ITSP A DigitMap - (optional) (1xxxxxxxxxx|<1555>[2-9]xxxxxxS3|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.) (as an example, replacing 1-555 with your local area code) will enable both 7 and 10-digit dial for North American numbers. See the manufacturer's technical reference manual for details of the syntax.
- Phone1 PrimaryLine - "SP1 service"
- SP1 ITSP Profile - A
- SP1 AuthUserName - 123456_1 (your voip.ms user number and a subaccount number, in this example user #123456 subaccount #1
- SP1 AuthPassword - the password associated with your voip.ms subsccount
If you have additional virtual lines, repeat the same configuration steps for each subaccount using SP2, SP3... up to a maximum of eight lines and ten handsets.
From the "SP1 Service" page, change the following settings for the first virtual "line" (the others will be similar):
- X_DisplayNumber - A short text string identifying this line on the local handset screen. Typically the seven-digit NXX-XXXX local number, although any value will do.
- X_InboundCallRoute - DT1,DT2,DT3 (if this number is to ring to the first three extensions, for example). The default (DT1) rings only to the first extension on inbound calls.
- X_AcceptSipFromRegistrarOnly - YES (to keep spurious calls out)
- X_KeepAliveEnable - YES (if you are behind NAT)
- X_KeepAliveExpires - 180 (three minutes) is reasonable
- DirectoryNumber - NPA-NXX-XXXX, the directory number associated with this line
- AuthUserName, AuthPassword - should already be set from the "Setup Wizard" above; if not, set them here.
- CallerIDName - your name (15 alphanumeric chars max, no punctuation but spaces are allowed) as you want it to appear on Caller ID for outbound calls.
- X_CheckVoiceMailNumber - *97
- MessageWaiting - YES
Save everything before leaving each page of the setup. When you are finished making changes, reboot the device.
Try a test call, such as the echo test (press [4] [4] [4] [3] and the [green] button). You should hear your own voice played back just as it was received.
See also
Documentation
This page is merely a brief overview with just enough information to connect the handsets to VoIP.ms; see the manufacturer's website (poly.com) for more extensive documentation:
- Quick start: handset + base, expansion handset + charger
- Admin guide and technical reference manual from Poly.com
