|
|
| (102 intermediate revisions not shown) |
| Line 1: |
Line 1: |
| - | == Manual Configuration details ==
| + | #REDIRECT [[OBi 100/110 & OBi 200]] |
| - | | + | |
| - | Dial ***1 from the connected phone, to get the IP address of your device.
| + | |
| - | | + | |
| - | '''Service Providers >> ITSP Profile >> SIP'''
| + | |
| - | | + | |
| - | Please note that in order to change the settings, you need to Uncheck the Default box on the right hand side.
| + | |
| - | | + | |
| - | *ProxyServer: atlanta.voip.ms (one of our multiple servers)
| + | |
| - | *ProxyServerPort: 5060
| + | |
| - | *RegistrarServer: atlanta.voip.ms (one of our multiple servers)
| + | |
| - | *RegistrarServerPort: 5060
| + | |
| - | | + | |
| - | '''Service Providers >> ITSP Profile >> General'''
| + | |
| - | | + | |
| - | *Name: 100000 (Your VoIP.ms username)
| + | |
| - |
| + | |
| - | '''Voice Services >> SP Service'''
| + | |
| - | | + | |
| - | *AuthUserName: 100000 (Your VoIP.ms username)
| + | |
| - | *AuthPassword: ********* (Account Password)
| + | |
| - | | + | |
| - | '''Checking your Voicemail'''
| + | |
| - | | + | |
| - | If you encounter any issues when you try to check your VoiP.MS [[Voicemail]]. Please try the following suggestions.
| + | |
| - | | + | |
| - | Try changing your Dial plan.
| + | |
| - | Replace the 555 digits in the following lines by the area code of your choice and copy the line, including parenthesis, in the Digitmap field in the ITSP Profile:
| + | |
| - | | + | |
| - | Default Dial Plan:
| + | |
| - | ((1xxxxxxxxxx|<1555>[2-9]xxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*]@@.)
| + | |
| - | | + | |
| - | Dial Plan to allow you to dial other numbers plus those beginning with * followed by one or more numbers:
| + | |
| - | (1xxxxxxxxxx|<1555>[2-9]xxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|*xx.|(Mipd)|[^*]@@.)
| + | |
| - | | + | |
| - | Dial Plan to allow you to dial other number plus *97 and *98 ONLY:
| + | |
| - | | + | |
| - | (1xxxxxxxxxx|<1555>[2-9]xxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|*9[78]|(Mipd)|[^*]@@.)
| + | |
| - | | + | |
| - | Also, some clients have been successful by dialing '''**1 and *97''' for line 1 or '''**2 and *97''' for line 2.
| + | |
| - | | + | |
| - | [[File:Obigeneral.jpg]]
| + | |
| - | [[File:Obisip.jpg]]
| + | |
| - | [[File:Obipart3.jpg]]
| + | |
| - | | + | |
| - | | + | |
| - | | + | |
| - | ''' ''An additional note regarding Outbound Calling'''''
| + | |
| - | | + | |
| - | | + | |
| - | | + | |
| - | In at least one instance it was necessary to specify a non-default outbound calling route in the Obi110 to be able to place calls using the voip.ms service. The default setting had the Obi110 attempting to place calls using the PSTN port on the device. The relevant setting is:
| + | |
| - | | + | |
| - | '''Physical Interfaces >> PHONE Port '''
| + | |
| - | *PrimaryLine: (Select from drop-down)
| + | |
| - | | + | |
| - | [[File:ObiPhoneport.JPG]]
| + | |
| - | | + | |
| - | The default is PSTN. Select SP1 Service if you only have one SIP account configured on the device. Select Trunk Group 1 to have it attempt to place calls using SP1 first, then SP2. Additional Trunk groups can be configured under Voice Services >> Gateways and Trunk Groups.
| + | |
| - | | + | |
| - | [[Category:Analog Telephone Adapters]]
| + | |
| - | | + | |
| - | == Configuration Using OBi Dashboard ==
| + | |
| - | | + | |
| - | I had added my device to the OBitalk network prior to trying the manual configuration details given on this page. I then attempted the manual configuration explained above. I found that after I submitted the changes, the settings would revert back to the default values after a short amount of time (I suspect a configuration mismatch was detected by the OBiTalk network and the previous configuration was automatically restored, but this is just supposition on my part). By configuring the device through the OBitalk dashboard and selecting ''voip.ms'' as the service provider the device was up and working with little effort.
| + | |
| - | | + | |
| - | Add your device to the OBitalk service in the OBi Dashboard [http://www.obitalk.com/obinet/]. Instructions for this are included with the obi110 and are not discussed here.
| + | |
| - | | + | |
| - | After the obi110 is added, edit the device. You can select '''Service Provider 1''' or '''Service Provider 2''' under the '''Configure Voice Services''' heading. This will take you to a page where you can select ''voip.ms''. Follow the instructions and once you are done the configuration will be downloaded to your obi110.
| + | |
