Solucion de Problemas con su DID

From VoIP.ms Wiki

[draft revision]

[draft revision]

Revision as of 15:16, 8 September 2011 (view source) Eric.voip.ms (Talk | contribs) (Created page with " "When I call my DID number, it is not reaching the destination I expect"... This is a common situation when talking about VoIP services, the proper way to test your DID Number ...") ← Older edit		Revision as of 20:55, 8 September 2011 (view source) Eric.voip.ms (Talk | contribs) Newer edit →
Line 1:		Line 1:
		+	" Cuando llamo a mi número DID, la llamada no alcanza el destino esperado"... Esto es una situación común cuando hablamos acerca de servicios VoIP, la manera correcta de probar un número DID con VoIP.ms es usando la aplicación "echo test" desde el portal del cliente, con esta herramienta usted puede verificar si su número esta funcionando correctamente.
		+	== Como probar su número con la aplicación "Echo Test" ==
-	"When I call my DID number, it is not reaching the destination I expect"... This is a common situation when talking about VoIP services, the proper way to test your DID Number with VoIP.ms is using the echo test application in the customer portal, with this feature you can verify if your number is working properly.	+	Usted puede usar esta herramienta siguiendo estas instrucciones:
-	== How to test your DID with Echo test ==	+	* Desde el portal del cliente, vaya al menú DID numbers -> submenú Manage DID(s), ahí podrá ver el listado completo de sus números DID.
-	You can use this tool following these steps:	+	* Al lado izquierdo de la descripción del número, usted encontrará 2 ligas, la primera es "Edit DID", haga click en esa liga.
-	* Go to DID Numbers >> Manage DID(s), once you get there you will see listed your DID number.	+	* Desde las opciones de Ruteo ( Routing ), seleccione "System" y de ese menú la opción "Echo test", vaya hacia la parte inferior de esa página y para salvar este cambio haga click en "apply changes".
-	* At the left side of the description for your number, you will find 2 links, the first one is to Edit the DID, click there.	+	[[File:Did1.jpg]]
-	* From the Routing options, select System >> Echo test, go to the bottom of the page and click on apply changes.	+	Una vez que su número este ruteado hacia "echo test", haga una llamada desde un número externo, preferentemente desde un número local, si el número esta funcionando correctamente, usted alcanzará la aplicación "echo test", después de la grabación usted puede "hablar" y el sistema de VoIP.ms repetirá todo lo que usted diga, con esto usted verifica la calidad de la linea. Si esta prueba es exitosa, podemos descartar cualquier posible problema relacionado con su número DID. En caso, de que usted, no pudiera alcanzar su número DID, mientras este se encuentra ruteado a "echo test", entonces no dude en contactar al departamento de soporte de VoIP.ms via ticket( support@voip.ms ).
-		+
-	[[File:Did1.jpg]]	+
-	Once your number is routed to the echo test mode, make a call from an external number, preferably a landline, if the number is working properly, you will reach the echo test, after the recording you can talk and the system will repeat everything you say, this to verify the quality of your line. If this test is successful, we can rule out any issue associated with the DID number itself. If you are unable to reach the DID while it is routed to echo test then please let the support staff know via ticket.	+	Nota Importante:
		+	-----
	Note: If possible try to repeat this test from at least 2-3 different lines to rule out any isues with the calling party.		Note: If possible try to repeat this test from at least 2-3 different lines to rule out any isues with the calling party.

---

Revision as of 20:55, 8 September 2011

" Cuando llamo a mi número DID, la llamada no alcanza el destino esperado"... Esto es una situación común cuando hablamos acerca de servicios VoIP, la manera correcta de probar un número DID con VoIP.ms es usando la aplicación "echo test" desde el portal del cliente, con esta herramienta usted puede verificar si su número esta funcionando correctamente.

Contents 1 Como probar su número con la aplicación "Echo Test" 2 Trouble shooting 2.1 VoIP.ms portal 2.2 Device configuration 2.3 Network configuration 3 Failover options

Como probar su número con la aplicación "Echo Test"

Usted puede usar esta herramienta siguiendo estas instrucciones:

• Desde el portal del cliente, vaya al menú DID numbers -> submenú Manage DID(s), ahí podrá ver el listado completo de sus números DID.

• Al lado izquierdo de la descripción del número, usted encontrará 2 ligas, la primera es "Edit DID", haga click en esa liga.

• Desde las opciones de Ruteo ( Routing ), seleccione "System" y de ese menú la opción "Echo test", vaya hacia la parte inferior de esa página y para salvar este cambio haga click en "apply changes".

Una vez que su número este ruteado hacia "echo test", haga una llamada desde un número externo, preferentemente desde un número local, si el número esta funcionando correctamente, usted alcanzará la aplicación "echo test", después de la grabación usted puede "hablar" y el sistema de VoIP.ms repetirá todo lo que usted diga, con esto usted verifica la calidad de la linea. Si esta prueba es exitosa, podemos descartar cualquier posible problema relacionado con su número DID. En caso, de que usted, no pudiera alcanzar su número DID, mientras este se encuentra ruteado a "echo test", entonces no dude en contactar al departamento de soporte de VoIP.ms via ticket( [email protected] ).

Nota Importante:

---

Note: If possible try to repeat this test from at least 2-3 different lines to rule out any isues with the calling party.

Trouble shooting

If you are able to reach the echo test recording while DID is in echo test, then the next possible reason for the unsuccessful calls could be something in your local network, VoIP.ms settings in your customer portal, or the device configuration can be affecting the function of our number. There are some importatn points we need to check for this.

VoIP.ms portal

• Check if your device is registered. Refer to Main Menu >> Portal Home, go to the Registration Status panel, to confirm if your device appear as registered in our Portal (This panel is only for SIP registrations).

• Verify if the POP (point of presence) that is configured for the DID, is matching the same server used by your device. Example: If your main account is registered in the Houston server, your POP needs to be there as well.

• If you are using the main account, go to Main menu >> Account Settings >> Inbound Settings, confirm the device type and protocol are set properly, depending on your device.

• When using a sub account, go to Sub Account >> Manage Sub Accounts, enter to edit the settings on the sub account in use, and select the correct device type.

Note: In both cases, make sure the setting NAT is set to Yes, this apply for the Main and Sub Account settings.

Device configuration

Sometime ATA devices lose registration after some time, usually because the local network closes the connection. Most devices have settings to prevent this.

• Using an ATA device or a softphone, check if it has any options similar to "Nat keep alive" or "Nat mapping", set these options to YES or Enable, to prevent the connection to go idle.

• Using a PBX or Asterisk system, is recommended to add qualify=yes and nat=yes in your configuration trunk.

Network configuration

• Make sure there is not any firewall or application in your network that could be blocking essential ports for the VoIP communication. For SIP: 5060 UDP RTP Range: 10001-20000 UDP, and for IAX2:4569 UDP.

• If you are behind a firewall or a router, make a test with the firewall disabled and bypass the router, to verify if these elements were affecting the calls.

When following this trouble shooting we can identify possible causes of an issue with our incoming calls, however will be important also to make use of the available options such "Failover" so we can keep receiving calls until we find a solution with our main route.

Failover options

On the Manage DID(s) section, enter again to edit the DID number settings. Under Routing, you will find a link to enable your Failover options, click on the link to display them. You will find 3 different options to set:

• Routing if Destination Busy: As the name indicates, in the case your number is busy, this option will trigger sending your call to the specific destination. Example: A call forward to an external number.

• Routing if Destination Unreachable: In the case you are not registered, a network issue (customer side) or power outage, this option will trigger.

• Routing if Destination No Answer: Self explanatory, if the main destination does not answer the call (Time out expired) this option will trigger.