3CX StartUP
From VoIP.ms Wiki
| [checked revision] | [checked revision] |
Joseanmont (Talk | contribs) |
Joseanmont (Talk | contribs) (→Adding Additional DIDs) |
||
| Line 69: | Line 69: | ||
== Adding Additional DIDs == | == Adding Additional DIDs == | ||
| - | To associate all other DIDs/Numbers you have in your VoIP.ms account with 3CX, you need to go to the | + | To associate all other DIDs/Numbers you have in your VoIP.ms account with 3CX, you need to go to back to the Trunk Settings in the Admin Console → Admin → Voice & Chat, click on the Edit option of your VoIP.ms Trunk and go to the “'''DID Numbers'''” tab. |
| - | Here you should already see 1 entry that is the Main Trunk number you have set. Add all other DIDs/Numbers you have to the list in the 10-digit number format (e.g. 6471234567) and press | + | Here you should already see 1 entry that is the Main Trunk number you have set. Add all other DIDs/Numbers you have to the list in the 10-digit number format (e.g. 6471234567) and press Save once you have finished. |
== Creating Inbound Rules == | == Creating Inbound Rules == | ||
Revision as of 17:32, 25 July 2023
Preconfigured, ready-to-go for up to 20-30 users in a shared instance. Recommended for most small businesses. StartUP is only available hosted by 3CX.
Contents |
VoIP.ms Configuration
Adjusting the device's type
The first thing is adjusting the Device type. To do so please navigate to Main Menu → Account settings → Inbound Settings and make sure that the Protocol for Inbound DIDs is set to “SIP” and that the Device type is set to “IP PBX Server” and apply any changes made.
Enabling rInstance on your Main Account
Next, head to Advanced tab and enable the option rInstance Parameter. That parameter is used for the Call Source Identification to match an incoming call with a SIP trunk on the registration-based trunk of 3CX.
Then you need to make sure that the DIDs ordered are linked to your account. To do so navigate to DID Numbers / Manage DID(s). Click on the Edit DID icon and make sure that the routing points to SIP/IAX and your main account.
Enabling rInstance on sub accounts
For sub accounts,rInstance Parameter can be found while creating or modifying your sub account under Advanced Options
Collecting 3CX Configuration Settings
In order to be able to register and operate the trunk in 3CX you will to gather some information that will be needed in the configuration of the trunk in 3CX.
- Username: The username for registering the trunk can be found under Main Menu → Account Information
- Password: The trunk password can be found in the email you received from VoIP.ms during the registration process. You can also change the password by navigating to Main Menu → Account Settings → Security.
- DID numbers: The DID numbers can be seen by navigating to DID Numbers → Manage DID(s)
- Registrar: Go to Main Menu → Account Settings → Default DID Routing. From here make note of the selected server. In this example the server is sanjose2.voip.ms.
Configuring the Trunk with 3CX
The instructions to sign up for a 3CX StartUP Free account and license can be found here.
For the StartUP license follow the instructions until the section Hosted - StartUP in the Step 2 and then skip to the Step 3.
Once you have finished activating your 3CX account and license you will be able to access your Admin Console and start setting up a trunk.
Adding the Trunk To add a trunk, click on the Admin button (the gears icon), then on Voice &chat and then click on + Add Trunk.
In the Add Trunk page, fill up the General tab with the following information:
- Country: CA
- Trunk: VoIP.ms
- Name: Any name of your choice.
- Main trunk number: Use the DID collected from the VoIP.ms portal. You must enter the number in the national number format (e.g. 6471234567)
- Registrar / Server: Enter the server that is set as the POP server of your DID (E.g. sanjose1.voip.ms).
- Authentication ID: Your Main SIP Account or Sub-Account username
- Authentication Password: The password of your Main SIP Account or Sub-Account
The server can be any of the VoIP.ms servers available here
Once you have filled in these fields, and set the "Outbound Parameters", press OK at the TOP of the page. At this point if you refresh the page you should see your VoIP.ms Trunk appear as Registered.
Adding Additional DIDs
To associate all other DIDs/Numbers you have in your VoIP.ms account with 3CX, you need to go to back to the Trunk Settings in the Admin Console → Admin → Voice & Chat, click on the Edit option of your VoIP.ms Trunk and go to the “DID Numbers” tab.
Here you should already see 1 entry that is the Main Trunk number you have set. Add all other DIDs/Numbers you have to the list in the 10-digit number format (e.g. 6471234567) and press Save once you have finished.
Creating Inbound Rules
Now that you have associated all your DIDs/Numbers with your SIP Trunk in 3CX, you can create Inbound Rules to set where calls will be routed when those numbers are called. Instructions on how to create Inbound Rules can be found here.
Outbound Caller ID
VoIP.ms Trunks support Clip No Screening which means you can present any number as outbound caller ID, regardless if it’s associated with your account or not. For this to work, in any field within 3CX where the Outbound Caller ID can be set, the numbers must be input in either a 10-digit (e.g. 6471234567), 11-digit format (e.g. 16471234567) or E164 format (e.g. +16471234567).
Outbound Rules
When configuring your Outbound Rules make sure that all numbers are dialed either in the 10-digit (e.g. 6471234567), 11-digit format (e.g. 16471234567) or E164 format (e.g. +116471234567).
More information about how to create Outbound Rules and how they work can be found here.
