TalkSwitch

 '''Disclaimer:''' Talkswitch Fortivoice System is not 100% guaranteed to work with VoIP.ms. The following
 configuration is the result of several real tests and feedback from our customers. This is by far the most reliable
 configuration that we have been able to acquire. Please follow the instructions as explained and contact us if you
 have any additional information or questions.

==='''Configuring TalkSwitch for VoIP.ms VoIP Service'''===

This guide will show you how to set up VoIP.ms VoIP service.

When you open an account with VoIP.ms, we will provide you with account credentials information. Use this information to set up the service provider profile and VoIP numbers on your TalkSwitch system.

''Setting up a service provider profile'' 

1. Select the VoIP Configuration page. 

[[File:Talkswitch1.png]]

2. Select a Profile (SP 1 to SP 4) that you wish to assign for FortiCall.

3. Select the Activate Profile checkbox.

4. Under Service Provider select Manual Setup.

5. Click the Update Configuration button. The essential settings will be completed automatically.

Disable public IP address substitution leave this unchecked.
Check Register with authentication username.
Check Enable NAT Keep alives (You can keep the default NAT settings)
Codec Options: Here make sure to select only the codec supported for VoIP.ms (g.729 and g.711u). And if you have enough bandwidth you should select the g.711u as Preferred codec.

[[File:Image002.png]]

===Provisioning Details===
*'''Proxy Server name''': server.voip.ms (one of the voip.ms servers, e.g. atlanta.voip.ms)
*'''Registrar server name''': same as above
*'''Outbound proxy''': same as above
*'''Realm/domain''': same as above

==Configuring Outgoing calls with VoIP.ms==

*Select the '''VoIP Numbers''' page

[[File:Voip number outbound (3).jpg|800px]]

*Select one of the empty voip number slots and then check the '''Activate VoIP number'''
*'''Select a VoIP profile''': Here select the profile to create for VoIP.ms

'''''Please enter your Main Account SIP userID as shown in the screen, this is required as this section sends the correct information required from our servers on the INVITES:FROM which will be the userid, if you don't add this record the Talkswitch will be sending the number (DID set) instead and this will result in continuous 'deregistrations' = registration dropping.'''''

===Username and Password===

*'''User/Account''': 100000 (Replace with your 6 digit Main SIP Account User ID or Sub Account username, i.e. 123456 or 123456_sub)

*'''Password''': (the password for your account. If you're using the main account this is the same you use to login to your Customer Portal, unless you change the password, if using a sub account you'll notice each sub account has their own password)

 '''Note''' You can only use the main account for outgoing calls, this is due to the Talkswitch system not supporting
 the Underscore on the sub accounts.

==Configuring Incoming calls with VoIP.ms==

 '''Note:''' You don't need to purchase a DID number for outgoing calls. The VoIP number is used as your CallerID number.

[[File:Voip number inbound (3).jpg|800px]]

Here you can set the callerID number that you want (or your DID number if you want to receive incoming calls), you need to enter the number filling in the 3 fields. 
*'''Country Code''': 1 
*'''City or area code''': 555
*'''Number''': 4443322


<!-- [[Category:PBXes]]

 '''Note:''' If you are planning to use more than 1 number with us, as you may know Talkswitch requires you to add different accounts for 
 incoming. You can use the sub accounts in this section, however on the customer portal you will need to set the sub accounts for IP 
 authentication and you will have to contact us in order to set all the sub accounts to the same IP address (currently the configuration 
 will require different IP addresses).

-->