Asterisk SIP

From VoIP.ms Wiki

You do not have permission to edit this page, for the following reasons:

• The action you have requested is limited to users in one of the groups: staff, customer.
• You must confirm your e-mail address before editing pages. Please set and validate your e-mail address through your user preferences.

You can view and copy the source of this page:

==Asterisk (SIP)== ===sip.conf=== <nowiki> [general] register => 100000:johnspassword@atlanta.voip.ms:5060 [voipms] canreinvite=no context=mycontext host=atlanta.voip.ms ;(one of our multiple servers, you can choose the one closer to your location) secret=johnspassword ;your password type=peer username=100000 ;(Replace with your 6 digit Main SIP Account User ID or Sub Account username, i.e. 123456 or 123456_sub) disallow=all allow=ulaw ; allow=g729 ; Uncomment if you support G729 fromuser=100000 ;(Replace with your 6 digit Main SIP Account User ID or Sub Account username, i.e. 123456 or 123456_sub) trustrpid=yes sendrpid=yes insecure=invite nat=yes </nowiki> *Note: As of FreePBX/Asterisk version 2.9.0.7 if ;comments are placed after the config entries as above it may prevent outgoing call's with the end points getting "All circuits are busy". Remove the ;comments and the trunk will send the calls with no errors. ===extensions.conf=== <nowiki> [mycontext] ; Make sure to include inbound prior to outbound because the _NXXNXXXXXX handler will match the incoming call and create a loop include => voipms-inbound include => voipms-outbound [voipms-outbound] exten => _1NXXNXXXXXX,1,Dial(SIP/${EXTEN}@voipms) exten => _1NXXNXXXXXX,n,Hangup() exten => _NXXNXXXXXX,1,Dial(SIP/1${EXTEN}@voipms) exten => _NXXNXXXXXX,n,Hangup() exten => _011.,1,Dial(SIP/${EXTEN}@voipms) exten => _011.,n,Hangup() exten => _00.,1,Dial(SIP/${EXTEN}@voipms) exten => _00.,n,Hangup() ; inbound context example for your DID numbers, do not add the number 1 in front [voipms-inbound] exten => 7863643011,1,Answer() ;your DID </nowiki> <br> ==Asterisk TLS/SRTP (SIP)== 1. In order to use these devices with encryption, besides having to [[Call Encryption - TLS/SRTP | enable the SIP account in your VoIP.ms customer portal]], there are some settings you will have to modify in your device's configuration. 2. Once your account/sub-account has Encrypted traffic enabled, the system has to be configured use/send the traffic through TLS and SRTP. For the registration over TLS, you need to define the protocol the PBX will use in the general config. [general] register => tls://100000:johnspassword@atlanta1.voip.ms:5061 For the outbound part, add the following lines to the peer details. encryption=yes transport=tls See example below: <nowiki> [voipms] encryption=yes transport=tls canreinvite=no context=mycontext host=atlanta1.voip.ms ;(one of our multiple servers, you can choose the one closer to your location) secret=johnspassword ;your password type=peer username=100000 ;(Replace with your 6 digit Main SIP Account User ID or Sub Account username, i.e. 123456 or 123456_sub) disallow=all allow=ulaw ; allow=g729 ; Uncomment if you support G729 fromuser=100000 ;(Replace with your 6 digit Main SIP Account User ID or Sub Account username, i.e. 123456 or 123456_sub) trustrpid=yes sendrpid=yes insecure=invite nat=yes </nowiki> '''Note:''' When using TLS is very important to specify the number of the server, in case the name you have chosen doesn't use the number 1 you need to add it. ==Asterisk IP Auth. (SIP)== ===sip.conf=== Note: You'll need to create a sub account to use IP Auth <nowiki> [voipms] canreinvite=nonat context=mycontext host=atlanta.voip.ms ;(one of our multiple servers, you can choose the one closer to your location) type=peer disallow=all allow=ulaw ; allow=g729 ; uncomment if you support g729 nat=yes </nowiki> ===extensions.conf=== <nowiki> [mycontext] ; Make sure to include inbound prior to outbound because the _NXXNXXXXXX handler will match the incoming call and create a loop include => voipms-inbound include => voipms-outbound [voipms-outbound] exten => _1NXXNXXXXXX,1,Dial(SIP/${EXTEN}@voipms) exten => _1NXXNXXXXXX,n,Hangup() exten => _NXXNXXXXXX,1,Dial(SIP/1${EXTEN}@voipms) exten => _NXXNXXXXXX,n,Hangup() exten => _011.,1,Dial(SIP/${EXTEN}@voipms) exten => _011.,n,Hangup() exten => _00.,1,Dial(SIP/${EXTEN}@voipms) exten => _00.,n,Hangup() ; inbound context example for your DID numbers, do not add the number 1 in front [voipms-inbound] exten => 7863643011,1,Answer() ;your DID </nowiki> ==Known Issues== ===Getting Message Waiting Indicator to Work with VoIP.ms Voicemail=== VoIP.ms sends MWI notifications unsolicited. Please make the following changes in your configurations. Remove this Line please. [general] Section mwi => 123456:mypassword@losangeles.voip.ms/65000 Add this Line please. [voipms] Section unsolicited_mailbox=65000 == Local extension calling == (User submitted) In order for this to work, you must fill out "User Context and User Details" User Context Name: 100000 (your account) [100000] your account type=user auth=md5 notransfer=yes disallow=all allow=gsm&ulaw trunk=yes secret=**** context=from-trunk <br><br><br><br><br>

Return to Asterisk SIP.