Grandstream HandyTone 502 - HT502 - VoIP.ms Wiki

Grandstream HandyTone 502 - HT502

From VoIP.ms Wiki

(Difference between revisions)
Jump to: navigation, search
[quality revision][quality revision]
(Known Issues and Resolutions)
(5 intermediate revisions not shown)
Line 3: Line 3:
==Configuration Detail==
==Configuration Detail==
 +
 +
[[File:502_frontandback.jpg]]
 +
 +
 +
 +
 +
'''Connect the HandyTone'''
 +
 +
1. Connect a standard touch-tone analog telephone (or fax machine) to PHONE port (or PHONE1,
 +
PHONE2 port for HT386/496/502).
 +
 +
2. Connect a PSTN telephone line to LINE port (optional, applies to HT386/486/488/503 only).
 +
 +
3. Insert the Ethernet cable into the Ethernet port (HT286/386) or WAN port (HT486/488/496/502/503) of
 +
HandyTone and connect the other end of the Ethernet cable to an uplink port (a router or a modem, etc.).
 +
 +
4. Connect a PC to the LAN port of HandyTone (optional, applies to HT486/488/496/502/503 only).
 +
 +
5. Insert the power adapter into the HandyTone and connect it to an electrical outlet.
 +
 +
6. Using the HandyTone embedded web server or IVR (Interactive Voice Prompt) menu, you can further
 +
configure the phone using either a static IP or DHCP.
 +
[[File:502.jpg]]
 +
 +
'''Configuring the HandyTone using a Web Browser'''
 +
 +
1. From the analog phone, press *** to get into the IVR menu. Enter option 02 to obtain the HandyTone’s IP
 +
address.
 +
 +
2. For HT486/488/496/502/503, please enable the “WAN side HTTP access” option by entering IVR
 +
option 12 and press 9. A reboot or power cycle of the HandyTone is required after this change. You can
 +
also access the HandyTone’s web configuration from a PC connected to the LAN port via 192.168.2.1.
 +
 +
3. Type the HandyTone’s IP address in your PC browser.
 +
 +
4. Log in using password “admin” to configure the HandyTone
 +
 +
 +
 +
[[File:5021.jpg]]
 +
'''Step 1:'''
'''Step 1:'''
Line 21: Line 62:
'''
'''
 +
== Known Issues and Resolutions ==
== Known Issues and Resolutions ==
'''
'''
Line 28: Line 70:
  You can also adjust the setting Gain, where the Rx (Other Person) is a gain level for signals transmitted by FXS and Tx (You)  
  You can also adjust the setting Gain, where the Rx (Other Person) is a gain level for signals transmitted by FXS and Tx (You)  
  is a gain level for signals received by FXS.
  is a gain level for signals received by FXS.
 +
 +
'''Receiving Weird Calls Like from CallerID 100 or in the middle of the Night not showing in your CDR:'''
 +
These calls are not going through our Network but rather through the internet directly to your ATA Device.
 +
Please check in the Web GUI under each FXS port tab that this option is enabled:  Allow Incoming SIP Messages from SIP Proxy Only: Set to YES.
 +
This will make sure you can only receive calls from VoIP.ms.
[[category: Analog Telephone Adapters]]
[[category: Analog Telephone Adapters]]

Revision as of 16:34, 4 September 2013

Grandstream HandyTone 502 - HT502

Configuration Detail

502 frontandback.jpg



Connect the HandyTone

1. Connect a standard touch-tone analog telephone (or fax machine) to PHONE port (or PHONE1, PHONE2 port for HT386/496/502).

2. Connect a PSTN telephone line to LINE port (optional, applies to HT386/486/488/503 only).

3. Insert the Ethernet cable into the Ethernet port (HT286/386) or WAN port (HT486/488/496/502/503) of HandyTone and connect the other end of the Ethernet cable to an uplink port (a router or a modem, etc.).

4. Connect a PC to the LAN port of HandyTone (optional, applies to HT486/488/496/502/503 only).

5. Insert the power adapter into the HandyTone and connect it to an electrical outlet.

6. Using the HandyTone embedded web server or IVR (Interactive Voice Prompt) menu, you can further configure the phone using either a static IP or DHCP. 502.jpg

Configuring the HandyTone using a Web Browser

1. From the analog phone, press *** to get into the IVR menu. Enter option 02 to obtain the HandyTone’s IP address.

2. For HT486/488/496/502/503, please enable the “WAN side HTTP access” option by entering IVR option 12 and press 9. A reboot or power cycle of the HandyTone is required after this change. You can also access the HandyTone’s web configuration from a PC connected to the LAN port via 192.168.2.1.

3. Type the HandyTone’s IP address in your PC browser.

4. Log in using password “admin” to configure the HandyTone


5021.jpg


Step 1:

Click on FXS 1 to configure your first line.


Step 2:

Fill the followings fields.

Known Issues and Resolutions

Hearing an Echo on the Line:

Please go to your FXS port setting screen, that you are using with us, and verify that the option Disable Line Echo Canceler, is set to NO.
You can also adjust the setting Gain, where the Rx (Other Person) is a gain level for signals transmitted by FXS and Tx (You) 
is a gain level for signals received by FXS.

Receiving Weird Calls Like from CallerID 100 or in the middle of the Night not showing in your CDR:

These calls are not going through our Network but rather through the internet directly to your ATA Device.
Please check in the Web GUI under each FXS port tab that this option is enabled:  Allow Incoming SIP Messages from SIP Proxy Only: Set to YES.
This will make sure you can only receive calls from VoIP.ms.
Personal tools
Namespaces
Variants
Actions
VoIP.ms Wiki
Configuration
Guides (English)
Guides (Français)
Guías (Español)
Toolbox