Cisco SPA112 - VoIP.ms Wiki

Cisco SPA112

From VoIP.ms Wiki

(Difference between revisions)
Jump to: navigation, search
[draft revision][draft revision]
m (Update firmware notice)
Line 2: Line 2:
<div style="width:100%;overflow:hidden;clear:both"></div>
<div style="width:100%;overflow:hidden;clear:both"></div>
-
  '''Make sure to install the latest firmware [http://www.cisco.com/go/smallbizvoicegateways].'''
+
  '''Make sure to install the latest firmware from http://www.cisco.com/go/smallbizvoicegateways.'''
-
  '''Version 1.1 or later should be used for proper Caller ID support. If a new revision is'''
+
  '''Version 1.1 or later should be used for proper Caller ID support. '''
-
'''not available, contact Cisco Small Business Support'''
+
== Configuration Details ==
== Configuration Details ==

Revision as of 01:56, 28 February 2012

Cisco SPA112
Make sure to install the latest firmware from http://www.cisco.com/go/smallbizvoicegateways.
Version 1.1 or later should be used for proper Caller ID support. 

Configuration Details

Step 1

Attach the Cisco SPA112 to your network and attach an analog phone to one of the phone ports, then do the following: Dial **** from the phone, even though there is no dial tone. When you hear "System Configuration Menu," dial 1 1 0 # slowly. The current IP address will be read back.

If you hear 0.0.0.0, check your network connection and DHCP server. If necessary, a static IP address
can be assigned by using option 111# at the IVR, then entering the IP address with your phone's keypad
(for example, 10*1*27*2 for 10.1.27.2). The network mask can be set with option 121# and the default
gateway can be sent with option 131#

Step 2

Open your web browser and go to the IP address you obtained in step 1 (for example, http://10.1.27.1). The default username is admin, and the default password is also admin.

Step 3

SPA112 Quick.PNG

Go to Quick Setup and configure Line 1 as follows:

Proxy: server_location.voip.ms

Display Name: Your name

User ID: Your VoIP.MS SIP Account number (or subaccount)

Password: Your VoIP.MS SIP Password

Dial Plan: (911S0|<:1555>[2-9]xxxxxx|1[2-9]xx[2-9]xxxxxxS0|[2-9]xx[2-9]xxxxxxS0|*xx|*xx.|[3468]11|822|0|00|[2-9]xxxxxx|4xxx|**275x.|xxxxxxxxxxxx.)

(note: replace 555 in the dial plan with your area code)

Click Submit to save settings.

Step 4

Click on Voice, then Line 1

Set NAT Mapping Enable to Yes, then set NAT Keep Alive Enable to Yes. If your environment does not use NAT, you can leave these settings disabled. These features can usually be disabled on the SPA122 if it is connected directly to your modem since its' traffic will not be subject to NAT in this configuration.

Under Proxy and Registration set Register Expires to 180, Proxy Fallback Intvl to 180

SPA112 NAT1.png

SPA112 Proxy1.png

Click Submit to submit these changes

Step 5

Click Network Setup, then go to Basic Setup, then click Time Settings

Set your time zone and (optional) NTP settings. A good time server choice is 0.pool.ntp.org. Setting the proper time zone will ensure that the time which appears on your Caller ID display is correct.

Click Submit to save the changes

Personal tools
Namespaces
Variants
Actions
VoIP.ms Wiki
Configuration
Guides (English)
Guides (Français)
Guías (Español)
Toolbox